# generated by PrusaSlicer 2.9.2 on 2026-02-24 at 18:05:51 UTC

[print:0.28mm height 0.4mm nozzle]
arc_fitting = disabled
automatic_extrusion_widths = 1
automatic_infill_combination = 0
automatic_infill_combination_max_layer_height = 100%
avoid_crossing_curled_overhangs = 0
avoid_crossing_perimeters = 0
avoid_crossing_perimeters_max_detour = 0
bed_temperature_extruder = 0
bottom_fill_pattern = rectilinear
bottom_solid_layers = 3
bottom_solid_min_thickness = 0
bridge_acceleration = 1500
bridge_angle = 0
bridge_flow_ratio = 0.95
bridge_speed = 50
brim_separation = 0
brim_type = outer_only
brim_width = 0
compatible_printers = 
compatible_printers_condition = printer_model=~/(ENDER|CR|SERMOON).*/ and nozzle_diameter[0]==0.4
complete_objects = 0
default_acceleration = 3000
dont_support_bridges = 1
draft_shield = disabled
elefant_foot_compensation = 0.3
enable_dynamic_overhang_speeds = 1
ensure_vertical_shell_thickness = enabled
external_perimeter_acceleration = 3000
external_perimeter_extrusion_width = 0
external_perimeter_speed = 200
external_perimeters_first = 1
extra_perimeters = 0
extra_perimeters_on_overhangs = 0
extrusion_width = 0
fill_angle = 45
fill_density = 15%
fill_pattern = honeycomb
first_layer_acceleration = 500
first_layer_acceleration_over_raft = 0
first_layer_extrusion_width = 0
first_layer_height = 0.28
first_layer_infill_speed = 0
first_layer_speed = 40
first_layer_speed_over_raft = 30
fuzzy_skin = none
fuzzy_skin_point_dist = 0.8
fuzzy_skin_thickness = 0.3
gap_fill_enabled = 1
gap_fill_speed = 120
gcode_comments = 0
gcode_label_objects = firmware
gcode_resolution = 0.0125
gcode_substitutions = 
infill_acceleration = 6000
infill_anchor = 600%
infill_anchor_max = 50
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0
infill_first = 0
infill_overlap = 0
infill_speed = 260
inherits = 
interface_shells = 0
interlocking_beam = 0
interlocking_beam_layer_count = 2
interlocking_beam_width = 0.8
interlocking_boundary_avoidance = 2
interlocking_depth = 2
interlocking_orientation = 22.5
ironing = 0
ironing_flowrate = 15%
ironing_spacing = 0.1
ironing_speed = 15
ironing_type = top
layer_height = 0.28
max_print_speed = 320
max_volumetric_extrusion_rate_slope_negative = 0
max_volumetric_extrusion_rate_slope_positive = 0
max_volumetric_speed = 0
min_bead_width = 85%
min_feature_size = 25%
min_skirt_length = 4
mmu_segmented_region_interlocking_depth = 0
mmu_segmented_region_max_width = 0
notes = 
only_one_perimeter_first_layer = 0
only_retract_when_crossing_perimeters = 0
ooze_prevention = 0
output_filename_format = {input_filename_base}_Thesus.gcode
over_bridge_speed = 0
overhang_speed_0 = 15
overhang_speed_1 = 15
overhang_speed_2 = 20
overhang_speed_3 = 50%
overhangs = 1
perimeter_acceleration = 6000
perimeter_extruder = 1
perimeter_extrusion_width = 0
perimeter_generator = arachne
perimeter_speed = 240
perimeters = 3
post_process = 
print_settings_id = 
raft_contact_distance = 0.1
raft_expansion = 1.5
raft_first_layer_density = 90%
raft_first_layer_expansion = 3
raft_layers = 0
resolution = 0
scarf_seam_entire_loop = 0
scarf_seam_length = 20
scarf_seam_max_segment_length = 1
scarf_seam_on_inner_perimeters = 0
scarf_seam_only_on_smooth = 1
scarf_seam_placement = nowhere
scarf_seam_start_height = 0%
seam_gap_distance = 15%
seam_position = aligned
single_extruder_multi_material_priming = 0
skirt_distance = 5
skirt_height = 2
skirts = 0
slice_closing_radius = 0.049
slicing_mode = regular
small_perimeter_speed = 170
solid_infill_acceleration = 6000
solid_infill_below_area = 0
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_width = 0
solid_infill_speed = 240
spiral_vase = 0
staggered_inner_seams = 0
standby_temperature_delta = -5
support_material = 0
support_material_angle = 0
support_material_auto = 0
support_material_bottom_contact_distance = 0
support_material_bottom_interface_layers = -1
support_material_buildplate_only = 0
support_material_closing_radius = 2
support_material_contact_distance = 0.15
support_material_enforce_layers = 0
support_material_extruder = 0
support_material_extrusion_width = 0
support_material_interface_contact_loops = 0
support_material_interface_extruder = 0
support_material_interface_layers = 0
support_material_interface_pattern = auto
support_material_interface_spacing = 0.2
support_material_interface_speed = 100%
support_material_pattern = honeycomb
support_material_spacing = 1
support_material_speed = 120
support_material_style = organic
support_material_synchronize_layers = 0
support_material_threshold = 40
support_material_with_sheath = 0
support_material_xy_spacing = 80%
support_tree_angle = 40
support_tree_angle_slow = 25
support_tree_branch_diameter = 2
support_tree_branch_diameter_angle = 5
support_tree_branch_diameter_double_wall = 3
support_tree_branch_distance = 1
support_tree_tip_diameter = 0.8
support_tree_top_rate = 30%
thick_bridges = 1
thin_walls = 0
top_fill_pattern = rectilinear
top_infill_extrusion_width = 0
top_one_perimeter_type = none
top_solid_infill_acceleration = 2000
top_solid_infill_speed = 100
top_solid_layers = 3
top_solid_min_thickness = 0
travel_acceleration = 6000
travel_speed = 320
travel_speed_z = 12
wall_distribution_count = 1
wall_transition_angle = 10
wall_transition_filter_deviation = 25%
wall_transition_length = 100%
wipe_tower = 0
wipe_tower_acceleration = 0
wipe_tower_bridging = 10
wipe_tower_brim_width = 2
wipe_tower_cone_angle = 0
wipe_tower_extra_flow = 100%
wipe_tower_extra_spacing = 100%
wipe_tower_extruder = 0
wipe_tower_no_sparse_layers = 0
wipe_tower_width = 60
xy_size_compensation = 0

[print:0.2mm height 0.4mm nozzle]
arc_fitting = disabled
automatic_extrusion_widths = 1
automatic_infill_combination = 0
automatic_infill_combination_max_layer_height = 100%
avoid_crossing_curled_overhangs = 0
avoid_crossing_perimeters = 0
avoid_crossing_perimeters_max_detour = 0
bed_temperature_extruder = 0
bottom_fill_pattern = rectilinear
bottom_solid_layers = 3
bottom_solid_min_thickness = 0
bridge_acceleration = 1500
bridge_angle = 0
bridge_flow_ratio = 0.95
bridge_speed = 50
brim_separation = 0
brim_type = outer_only
brim_width = 0
compatible_printers = 
compatible_printers_condition = printer_model=~/(ENDER|CR|SERMOON).*/ and nozzle_diameter[0]==0.4
complete_objects = 0
default_acceleration = 3000
dont_support_bridges = 1
draft_shield = disabled
elefant_foot_compensation = 0.3
enable_dynamic_overhang_speeds = 1
ensure_vertical_shell_thickness = enabled
external_perimeter_acceleration = 3000
external_perimeter_extrusion_width = 0
external_perimeter_speed = 200
external_perimeters_first = 1
extra_perimeters = 0
extra_perimeters_on_overhangs = 0
extrusion_width = 0
fill_angle = 45
fill_density = 15%
fill_pattern = honeycomb
first_layer_acceleration = 500
first_layer_acceleration_over_raft = 0
first_layer_extrusion_width = 0
first_layer_height = 0.2
first_layer_infill_speed = 0
first_layer_speed = 40
first_layer_speed_over_raft = 30
fuzzy_skin = none
fuzzy_skin_point_dist = 0.8
fuzzy_skin_thickness = 0.3
gap_fill_enabled = 1
gap_fill_speed = 120
gcode_comments = 0
gcode_label_objects = firmware
gcode_resolution = 0.0125
gcode_substitutions = 
infill_acceleration = 6000
infill_anchor = 600%
infill_anchor_max = 50
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0
infill_first = 0
infill_overlap = 0
infill_speed = 260
inherits = 
interface_shells = 0
interlocking_beam = 0
interlocking_beam_layer_count = 2
interlocking_beam_width = 0.8
interlocking_boundary_avoidance = 2
interlocking_depth = 2
interlocking_orientation = 22.5
ironing = 0
ironing_flowrate = 15%
ironing_spacing = 0.1
ironing_speed = 15
ironing_type = top
layer_height = 0.2
max_print_speed = 320
max_volumetric_extrusion_rate_slope_negative = 0
max_volumetric_extrusion_rate_slope_positive = 0
max_volumetric_speed = 0
min_bead_width = 85%
min_feature_size = 25%
min_skirt_length = 4
mmu_segmented_region_interlocking_depth = 0
mmu_segmented_region_max_width = 0
notes = 
only_one_perimeter_first_layer = 0
only_retract_when_crossing_perimeters = 0
ooze_prevention = 0
output_filename_format = {input_filename_base}_Thesus.gcode
over_bridge_speed = 0
overhang_speed_0 = 15
overhang_speed_1 = 15
overhang_speed_2 = 20
overhang_speed_3 = 50%
overhangs = 1
perimeter_acceleration = 6000
perimeter_extruder = 1
perimeter_extrusion_width = 0
perimeter_generator = arachne
perimeter_speed = 240
perimeters = 3
post_process = 
print_settings_id = 
raft_contact_distance = 0.1
raft_expansion = 1.5
raft_first_layer_density = 90%
raft_first_layer_expansion = 3
raft_layers = 0
resolution = 0
scarf_seam_entire_loop = 0
scarf_seam_length = 20
scarf_seam_max_segment_length = 1
scarf_seam_on_inner_perimeters = 0
scarf_seam_only_on_smooth = 1
scarf_seam_placement = nowhere
scarf_seam_start_height = 0%
seam_gap_distance = 15%
seam_position = aligned
single_extruder_multi_material_priming = 0
skirt_distance = 5
skirt_height = 2
skirts = 0
slice_closing_radius = 0.049
slicing_mode = regular
small_perimeter_speed = 170
solid_infill_acceleration = 6000
solid_infill_below_area = 0
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_width = 0
solid_infill_speed = 240
spiral_vase = 0
staggered_inner_seams = 0
standby_temperature_delta = -5
support_material = 0
support_material_angle = 0
support_material_auto = 0
support_material_bottom_contact_distance = 0
support_material_bottom_interface_layers = -1
support_material_buildplate_only = 0
support_material_closing_radius = 2
support_material_contact_distance = 0.15
support_material_enforce_layers = 0
support_material_extruder = 0
support_material_extrusion_width = 0
support_material_interface_contact_loops = 0
support_material_interface_extruder = 0
support_material_interface_layers = 0
support_material_interface_pattern = auto
support_material_interface_spacing = 0.2
support_material_interface_speed = 100%
support_material_pattern = honeycomb
support_material_spacing = 1
support_material_speed = 120
support_material_style = organic
support_material_synchronize_layers = 0
support_material_threshold = 40
support_material_with_sheath = 0
support_material_xy_spacing = 80%
support_tree_angle = 40
support_tree_angle_slow = 25
support_tree_branch_diameter = 2
support_tree_branch_diameter_angle = 5
support_tree_branch_diameter_double_wall = 3
support_tree_branch_distance = 1
support_tree_tip_diameter = 0.8
support_tree_top_rate = 30%
thick_bridges = 1
thin_walls = 0
top_fill_pattern = rectilinear
top_infill_extrusion_width = 0
top_one_perimeter_type = none
top_solid_infill_acceleration = 2000
top_solid_infill_speed = 100
top_solid_layers = 3
top_solid_min_thickness = 0
travel_acceleration = 6000
travel_speed = 320
travel_speed_z = 12
wall_distribution_count = 1
wall_transition_angle = 10
wall_transition_filter_deviation = 25%
wall_transition_length = 100%
wipe_tower = 0
wipe_tower_acceleration = 0
wipe_tower_bridging = 10
wipe_tower_brim_width = 2
wipe_tower_cone_angle = 0
wipe_tower_extra_flow = 100%
wipe_tower_extra_spacing = 100%
wipe_tower_extruder = 0
wipe_tower_no_sparse_layers = 0
wipe_tower_width = 60
xy_size_compensation = 0

[print:TPU 0.2 height 0.4mm nozzle]
arc_fitting = emit_center
automatic_extrusion_widths = 1
automatic_infill_combination = 0
automatic_infill_combination_max_layer_height = 100%
avoid_crossing_curled_overhangs = 0
avoid_crossing_perimeters = 0
avoid_crossing_perimeters_max_detour = 0
bed_temperature_extruder = 0
bottom_fill_pattern = rectilinear
bottom_solid_layers = 2
bottom_solid_min_thickness = 0
bridge_acceleration = 1500
bridge_angle = 0
bridge_flow_ratio = 0.95
bridge_speed = 100
brim_separation = 0
brim_type = outer_only
brim_width = 0
compatible_printers = 
compatible_printers_condition = printer_model=~/(ENDER|CR|SERMOON).*/ and nozzle_diameter[0]==0.4
complete_objects = 0
default_acceleration = 3000
dont_support_bridges = 1
draft_shield = disabled
elefant_foot_compensation = 0.3
enable_dynamic_overhang_speeds = 0
ensure_vertical_shell_thickness = enabled
external_perimeter_acceleration = 3000
external_perimeter_extrusion_width = 0
external_perimeter_speed = 175
external_perimeters_first = 1
extra_perimeters = 0
extra_perimeters_on_overhangs = 0
extrusion_width = 0
fill_angle = 45
fill_density = 8%
fill_pattern = gyroid
first_layer_acceleration = 5090
first_layer_acceleration_over_raft = 0
first_layer_extrusion_width = 0
first_layer_height = 0.2
first_layer_infill_speed = 0
first_layer_speed = 25%
first_layer_speed_over_raft = 30
fuzzy_skin = none
fuzzy_skin_point_dist = 0.8
fuzzy_skin_thickness = 0.3
gap_fill_enabled = 1
gap_fill_speed = 80
gcode_comments = 0
gcode_label_objects = firmware
gcode_resolution = 0.0125
gcode_substitutions = 
infill_acceleration = 6000
infill_anchor = 600%
infill_anchor_max = 50
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0
infill_first = 0
infill_overlap = 0
infill_speed = 175
inherits = 
interface_shells = 0
interlocking_beam = 0
interlocking_beam_layer_count = 2
interlocking_beam_width = 0.8
interlocking_boundary_avoidance = 2
interlocking_depth = 2
interlocking_orientation = 22.5
ironing = 0
ironing_flowrate = 15%
ironing_spacing = 0.1
ironing_speed = 15
ironing_type = top
layer_height = 0.2
max_print_speed = 260
max_volumetric_extrusion_rate_slope_negative = 0
max_volumetric_extrusion_rate_slope_positive = 0
max_volumetric_speed = 0
min_bead_width = 85%
min_feature_size = 25%
min_skirt_length = 4
mmu_segmented_region_interlocking_depth = 0
mmu_segmented_region_max_width = 0
notes = 
only_one_perimeter_first_layer = 0
only_retract_when_crossing_perimeters = 0
ooze_prevention = 0
output_filename_format = {input_filename_base}_Thesus.gcode
over_bridge_speed = 0
overhang_speed_0 = 15
overhang_speed_1 = 15
overhang_speed_2 = 20
overhang_speed_3 = 25
overhangs = 1
perimeter_acceleration = 6000
perimeter_extruder = 1
perimeter_extrusion_width = 0
perimeter_generator = arachne
perimeter_speed = 240
perimeters = 6
post_process = 
print_settings_id = 
raft_contact_distance = 0.1
raft_expansion = 1.5
raft_first_layer_density = 90%
raft_first_layer_expansion = 3
raft_layers = 0
resolution = 0
scarf_seam_entire_loop = 0
scarf_seam_length = 20
scarf_seam_max_segment_length = 1
scarf_seam_on_inner_perimeters = 0
scarf_seam_only_on_smooth = 1
scarf_seam_placement = nowhere
scarf_seam_start_height = 0%
seam_gap_distance = 15%
seam_position = aligned
single_extruder_multi_material_priming = 0
skirt_distance = 5
skirt_height = 2
skirts = 0
slice_closing_radius = 0.049
slicing_mode = regular
small_perimeter_speed = 40%
solid_infill_acceleration = 6000
solid_infill_below_area = 0
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_width = 0
solid_infill_speed = 200
spiral_vase = 0
staggered_inner_seams = 0
standby_temperature_delta = -5
support_material = 1
support_material_angle = 0
support_material_auto = 1
support_material_bottom_contact_distance = 0
support_material_bottom_interface_layers = -1
support_material_buildplate_only = 1
support_material_closing_radius = 2
support_material_contact_distance = 0.15
support_material_enforce_layers = 0
support_material_extruder = 0
support_material_extrusion_width = 0
support_material_interface_contact_loops = 0
support_material_interface_extruder = 0
support_material_interface_layers = 0
support_material_interface_pattern = auto
support_material_interface_spacing = 0.2
support_material_interface_speed = 100%
support_material_pattern = honeycomb
support_material_spacing = 1
support_material_speed = 100
support_material_style = organic
support_material_synchronize_layers = 0
support_material_threshold = 40
support_material_with_sheath = 0
support_material_xy_spacing = 80%
support_tree_angle = 40
support_tree_angle_slow = 25
support_tree_branch_diameter = 2
support_tree_branch_diameter_angle = 5
support_tree_branch_diameter_double_wall = 3
support_tree_branch_distance = 1
support_tree_tip_diameter = 0.8
support_tree_top_rate = 30%
thick_bridges = 1
thin_walls = 0
top_fill_pattern = rectilinear
top_infill_extrusion_width = 0
top_one_perimeter_type = none
top_solid_infill_acceleration = 2000
top_solid_infill_speed = 180
top_solid_layers = 4
top_solid_min_thickness = 0
travel_acceleration = 6000
travel_speed = 240
travel_speed_z = 0
wall_distribution_count = 1
wall_transition_angle = 10
wall_transition_filter_deviation = 25%
wall_transition_length = 100%
wipe_tower = 0
wipe_tower_acceleration = 0
wipe_tower_bridging = 10
wipe_tower_brim_width = 2
wipe_tower_cone_angle = 0
wipe_tower_extra_flow = 100%
wipe_tower_extra_spacing = 100%
wipe_tower_extruder = 0
wipe_tower_no_sparse_layers = 0
wipe_tower_width = 60
xy_size_compensation = 0

[filament:CF-PLA]
bed_temperature = 60
bridge_fan_speed = 100
chamber_minimal_temperature = 0
chamber_temperature = 0
compatible_printers = 
compatible_printers_condition = printer_notes!~/.*NO_TEMPLATES.*/ and printer_notes!~/.*PRINTER_VENDOR_TRILAB.*/ and printer_notes!~/.*PRINTER_MODEL_MK4IS.*/ and ! (printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and num_extruders>1) and printer_model == "Snapmaker A250 Dual"
compatible_prints = 
compatible_prints_condition = 
cooling = 1
disable_fan_first_layers = 1
enable_dynamic_fan_speeds = 0
end_filament_gcode = ";END gcode for filament\nG0 X{wipe_tower_x} Y{wipe_tower_y}"
extrusion_multiplier = 1
fan_always_on = 1
fan_below_layer_time = 100
filament_abrasive = 0
filament_colour = #FF8000
filament_cooling_final_speed = 2
filament_cooling_initial_speed = 3
filament_cooling_moves = 1
filament_cost = 25.4
filament_density = 1.24
filament_deretract_speed = nil
filament_diameter = 1.75
filament_infill_max_crossing_speed = 0
filament_infill_max_speed = 0
filament_load_time = 0
filament_loading_speed = 14
filament_loading_speed_start = 19
filament_max_volumetric_speed = 0
filament_minimal_purge_on_wipe_tower = 0
filament_multitool_ramming = 0
filament_multitool_ramming_flow = 10
filament_multitool_ramming_volume = 10
filament_notes = ""
filament_purge_multiplier = 100%
filament_ramming_parameters = "130 120 2.70968 2.93548 3.32258 3.83871 4.58065 5.54839 6.51613 7.35484 7.93548 8.16129| 0.05 2.66451 0.45 3.05805 0.95 4.05807 1.45 5.97742 1.95 7.69999 2.45 8.1936 2.95 11.342 3.45 11.4065 3.95 7.6 4.45 7.6 4.95 7.6"
filament_retract_before_travel = nil
filament_retract_before_wipe = nil
filament_retract_layer_change = nil
filament_retract_length = nil
filament_retract_length_toolchange = nil
filament_retract_lift = nil
filament_retract_lift_above = nil
filament_retract_lift_below = nil
filament_retract_restart_extra = nil
filament_retract_restart_extra_toolchange = nil
filament_retract_speed = nil
filament_seam_gap_distance = nil
filament_settings_id = ""
filament_shrinkage_compensation_xy = 0%
filament_shrinkage_compensation_z = 0%
filament_soluble = 0
filament_spool_weight = 0
filament_stamping_distance = 0
filament_stamping_loading_speed = 20
filament_toolchange_delay = 0
filament_travel_lift_before_obstacle = nil
filament_travel_max_lift = nil
filament_travel_ramping_lift = nil
filament_travel_slope = nil
filament_type = PLA
filament_unload_time = 0
filament_unloading_speed = 20
filament_unloading_speed_start = 100
filament_vendor = Generic
filament_wipe = nil
first_layer_bed_temperature = 60
first_layer_temperature = 215
full_fan_speed_layer = 3
idle_temperature = nil
inherits = 
max_fan_speed = 100
min_fan_speed = 100
min_print_speed = 10
overhang_fan_speed_0 = 0
overhang_fan_speed_1 = 0
overhang_fan_speed_2 = 0
overhang_fan_speed_3 = 0
slowdown_below_layer_time = 5
start_filament_gcode = "; Filament gcode\n"
temperature = 210

[filament:PETG]
bed_temperature = 80
bridge_fan_speed = 80
chamber_minimal_temperature = 0
chamber_temperature = 0
compatible_printers = 
compatible_printers_condition = printer_notes!~/.*NO_TEMPLATES.*/ and printer_notes!~/.*PRINTER_VENDOR_TRILAB.*/ and printer_notes!~/.*PRINTER_MODEL_MK4IS.*/ and ! (printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and num_extruders>1)
compatible_prints = 
compatible_prints_condition = 
cooling = 1
disable_fan_first_layers = 3
enable_dynamic_fan_speeds = 0
end_filament_gcode = "; Filament-specific end gcode\nM221 S100"
extrusion_multiplier = 0.75
fan_always_on = 0
fan_below_layer_time = 20
filament_abrasive = 0
filament_colour = #FF8000
filament_cooling_final_speed = 2
filament_cooling_initial_speed = 3
filament_cooling_moves = 1
filament_cost = 27.82
filament_density = 1.27
filament_deretract_speed = 25
filament_diameter = 1.75
filament_infill_max_crossing_speed = 0
filament_infill_max_speed = 0
filament_load_time = 0
filament_loading_speed = 14
filament_loading_speed_start = 19
filament_max_volumetric_speed = 0
filament_minimal_purge_on_wipe_tower = 0
filament_multitool_ramming = 0
filament_multitool_ramming_flow = 10
filament_multitool_ramming_volume = 10
filament_notes = ""
filament_purge_multiplier = 100%
filament_ramming_parameters = "130 120 2.70968 2.93548 3.32258 3.83871 4.58065 5.54839 6.51613 7.35484 7.93548 8.16129| 0.05 2.66451 0.45 3.05805 0.95 4.05807 1.45 5.97742 1.95 7.69999 2.45 8.1936 2.95 11.342 3.45 11.4065 3.95 7.6 4.45 7.6 4.95 7.6"
filament_retract_before_travel = nil
filament_retract_before_wipe = nil
filament_retract_layer_change = nil
filament_retract_length = 2
filament_retract_length_toolchange = nil
filament_retract_lift = nil
filament_retract_lift_above = nil
filament_retract_lift_below = 1
filament_retract_restart_extra = nil
filament_retract_restart_extra_toolchange = nil
filament_retract_speed = 25
filament_seam_gap_distance = nil
filament_settings_id = ""
filament_shrinkage_compensation_xy = 0%
filament_shrinkage_compensation_z = 0%
filament_soluble = 0
filament_spool_weight = 230
filament_stamping_distance = 0
filament_stamping_loading_speed = 20
filament_toolchange_delay = 0
filament_travel_lift_before_obstacle = nil
filament_travel_max_lift = nil
filament_travel_ramping_lift = nil
filament_travel_slope = nil
filament_type = PETG
filament_unload_time = 0
filament_unloading_speed = 20
filament_unloading_speed_start = 100
filament_vendor = Made for Prusa
filament_wipe = 1
first_layer_bed_temperature = 80
first_layer_temperature = 240
full_fan_speed_layer = 5
idle_temperature = nil
inherits = 
max_fan_speed = 40
min_fan_speed = 0
min_print_speed = 10
overhang_fan_speed_0 = 0
overhang_fan_speed_1 = 0
overhang_fan_speed_2 = 0
overhang_fan_speed_3 = 0
slowdown_below_layer_time = 15
start_filament_gcode = "; Filament gcode\nM221 S80"
temperature = 240

[filament:PLA]
bed_temperature = 60
bridge_fan_speed = 100
chamber_minimal_temperature = 0
chamber_temperature = 0
compatible_printers = 
compatible_printers_condition = printer_notes!~/.*NO_TEMPLATES.*/ and printer_notes!~/.*PRINTER_VENDOR_TRILAB.*/ and printer_notes!~/.*PRINTER_MODEL_MK4IS.*/ and ! (printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and num_extruders>1)
compatible_prints = 
compatible_prints_condition = 
cooling = 1
disable_fan_first_layers = 1
enable_dynamic_fan_speeds = 0
end_filament_gcode = "; Filament-specific end gcode"
extrusion_multiplier = 1
fan_always_on = 1
fan_below_layer_time = 100
filament_abrasive = 0
filament_colour = #FF8000
filament_cooling_final_speed = 2
filament_cooling_initial_speed = 3
filament_cooling_moves = 1
filament_cost = 27.82
filament_density = 1.24
filament_deretract_speed = nil
filament_diameter = 1.75
filament_infill_max_crossing_speed = 0
filament_infill_max_speed = 0
filament_load_time = 0
filament_loading_speed = 14
filament_loading_speed_start = 19
filament_max_volumetric_speed = 0
filament_minimal_purge_on_wipe_tower = 0
filament_multitool_ramming = 0
filament_multitool_ramming_flow = 10
filament_multitool_ramming_volume = 10
filament_notes = ""
filament_purge_multiplier = 100%
filament_ramming_parameters = "130 120 2.70968 2.93548 3.32258 3.83871 4.58065 5.54839 6.51613 7.35484 7.93548 8.16129| 0.05 2.66451 0.45 3.05805 0.95 4.05807 1.45 5.97742 1.95 7.69999 2.45 8.1936 2.95 11.342 3.45 11.4065 3.95 7.6 4.45 7.6 4.95 7.6"
filament_retract_before_travel = nil
filament_retract_before_wipe = nil
filament_retract_layer_change = nil
filament_retract_length = nil
filament_retract_length_toolchange = nil
filament_retract_lift = nil
filament_retract_lift_above = nil
filament_retract_lift_below = nil
filament_retract_restart_extra = nil
filament_retract_restart_extra_toolchange = nil
filament_retract_speed = nil
filament_seam_gap_distance = nil
filament_settings_id = ""
filament_shrinkage_compensation_xy = 0%
filament_shrinkage_compensation_z = 0%
filament_soluble = 0
filament_spool_weight = 230
filament_stamping_distance = 0
filament_stamping_loading_speed = 20
filament_toolchange_delay = 0
filament_travel_lift_before_obstacle = nil
filament_travel_max_lift = nil
filament_travel_ramping_lift = nil
filament_travel_slope = nil
filament_type = PLA
filament_unload_time = 0
filament_unloading_speed = 20
filament_unloading_speed_start = 100
filament_vendor = Made for Prusa
filament_wipe = nil
first_layer_bed_temperature = 60
first_layer_temperature = 220
full_fan_speed_layer = 3
idle_temperature = nil
inherits = 
max_fan_speed = 100
min_fan_speed = 100
min_print_speed = 10
overhang_fan_speed_0 = 0
overhang_fan_speed_1 = 0
overhang_fan_speed_2 = 0
overhang_fan_speed_3 = 0
slowdown_below_layer_time = 10
start_filament_gcode = "; Filament gcode\n"
temperature = 215

[filament:TPU]
bed_temperature = 30
bridge_fan_speed = 100
chamber_minimal_temperature = 0
chamber_temperature = 0
compatible_printers = 
compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_CREALITY.*/
compatible_prints = 
compatible_prints_condition = 
cooling = 0
disable_fan_first_layers = 1
enable_dynamic_fan_speeds = 0
end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n"
extrusion_multiplier = 1.16
fan_always_on = 1
fan_below_layer_time = 20
filament_abrasive = 0
filament_colour = #4D9398
filament_cooling_final_speed = 3.4
filament_cooling_initial_speed = 2.2
filament_cooling_moves = 4
filament_cost = 34.99
filament_density = 1.21
filament_deretract_speed = nil
filament_diameter = 1.75
filament_infill_max_crossing_speed = 0
filament_infill_max_speed = 0
filament_load_time = 0
filament_loading_speed = 28
filament_loading_speed_start = 3
filament_max_volumetric_speed = 0
filament_minimal_purge_on_wipe_tower = 15
filament_multitool_ramming = 0
filament_multitool_ramming_flow = 10
filament_multitool_ramming_volume = 10
filament_notes = ""
filament_purge_multiplier = 100%
filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
filament_retract_before_travel = nil
filament_retract_before_wipe = nil
filament_retract_layer_change = nil
filament_retract_length = 2
filament_retract_length_toolchange = nil
filament_retract_lift = nil
filament_retract_lift_above = nil
filament_retract_lift_below = nil
filament_retract_restart_extra = nil
filament_retract_restart_extra_toolchange = nil
filament_retract_speed = 30
filament_seam_gap_distance = nil
filament_settings_id = ""
filament_shrinkage_compensation_xy = 0%
filament_shrinkage_compensation_z = 0%
filament_soluble = 0
filament_spool_weight = 0
filament_stamping_distance = 0
filament_stamping_loading_speed = 20
filament_toolchange_delay = 0
filament_travel_lift_before_obstacle = nil
filament_travel_max_lift = nil
filament_travel_ramping_lift = nil
filament_travel_slope = nil
filament_type = TPU
filament_unload_time = 0
filament_unloading_speed = 90
filament_unloading_speed_start = 100
filament_vendor = Eolas Prints
filament_wipe = nil
first_layer_bed_temperature = 30
first_layer_temperature = 235
full_fan_speed_layer = 2
idle_temperature = 130
inherits = 
max_fan_speed = 0
min_fan_speed = 100
min_print_speed = 15
overhang_fan_speed_0 = 0
overhang_fan_speed_1 = 0
overhang_fan_speed_2 = 0
overhang_fan_speed_3 = 0
slowdown_below_layer_time = 20
start_filament_gcode = "; Filament gcode\n"
temperature = 235

[filament:TPU 93A]
bed_temperature = 30
bridge_fan_speed = 100
chamber_minimal_temperature = 0
chamber_temperature = 0
compatible_printers = 
compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_CREALITY.*/
compatible_prints = 
compatible_prints_condition = 
cooling = 0
disable_fan_first_layers = 1
enable_dynamic_fan_speeds = 0
end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n"
extrusion_multiplier = 1.16
fan_always_on = 1
fan_below_layer_time = 20
filament_abrasive = 0
filament_colour = #4D9398
filament_cooling_final_speed = 3.4
filament_cooling_initial_speed = 2.2
filament_cooling_moves = 4
filament_cost = 34.99
filament_density = 1.21
filament_deretract_speed = nil
filament_diameter = 1.75
filament_infill_max_crossing_speed = 0
filament_infill_max_speed = 0
filament_load_time = 0
filament_loading_speed = 28
filament_loading_speed_start = 3
filament_max_volumetric_speed = 1.2
filament_minimal_purge_on_wipe_tower = 15
filament_multitool_ramming = 0
filament_multitool_ramming_flow = 10
filament_multitool_ramming_volume = 10
filament_notes = ""
filament_purge_multiplier = 100%
filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
filament_retract_before_travel = nil
filament_retract_before_wipe = nil
filament_retract_layer_change = nil
filament_retract_length = 0
filament_retract_length_toolchange = nil
filament_retract_lift = nil
filament_retract_lift_above = nil
filament_retract_lift_below = nil
filament_retract_restart_extra = nil
filament_retract_restart_extra_toolchange = nil
filament_retract_speed = nil
filament_seam_gap_distance = nil
filament_settings_id = ""
filament_shrinkage_compensation_xy = 0%
filament_shrinkage_compensation_z = 0%
filament_soluble = 0
filament_spool_weight = 0
filament_stamping_distance = 0
filament_stamping_loading_speed = 20
filament_toolchange_delay = 0
filament_travel_lift_before_obstacle = nil
filament_travel_max_lift = nil
filament_travel_ramping_lift = nil
filament_travel_slope = nil
filament_type = TPU
filament_unload_time = 0
filament_unloading_speed = 90
filament_unloading_speed_start = 100
filament_vendor = Eolas Prints
filament_wipe = nil
first_layer_bed_temperature = 30
first_layer_temperature = 235
full_fan_speed_layer = 2
idle_temperature = 130
inherits = 
max_fan_speed = 0
min_fan_speed = 100
min_print_speed = 15
overhang_fan_speed_0 = 0
overhang_fan_speed_1 = 0
overhang_fan_speed_2 = 0
overhang_fan_speed_3 = 0
slowdown_below_layer_time = 20
start_filament_gcode = "; Filament gcode\n"
temperature = 235

[printer:Thesus]
autoemit_temperature_commands = 0
bed_custom_model = 
bed_custom_texture = /home/hackerspace/Prusa/pei_sheet_textured.png
bed_shape = 0x0,235x0,235x235,0x235
before_layer_gcode = ;BEFORE_LAYER_CHANGE\n;G92 E0\n;{layer_z}\n\n
between_objects_gcode = 
binary_gcode = 0
color_change_gcode = M600
cooling_tube_length = 5
cooling_tube_retraction = 91.5
default_filament_profile = CF-PLA
default_print_profile = "0.24mm 0.4 nozzle SPEED"
deretract_speed = 50
end_gcode = {if max_layer_z < max_print_height}G1 Z{z_offset+min(max_layer_z+2, max_print_height)} F600 ; Move print head up{endif}\nG1 X5 Y{print_bed_max[1]*0.85} F{travel_speed*60} ; present print\n{if max_layer_z < max_print_height-10}G1 Z{z_offset+min(max_layer_z+70, max_print_height-10)} F600 ; Move print head further up{endif}\n{if max_layer_z < max_print_height*0.6}G1 Z{max_print_height*0.6} F600 ; Move print head further up{endif}\nM140 S0 ; turn off heatbed\nM104 S0 ; turn off temperature\nM107 ; turn off fan\nM84 X Y E ; disable motors
extra_loading_move = -2
extruder_clearance_height = 20
extruder_clearance_radius = 20
extruder_colour = #FCE94F
extruder_offset = 0x0
gcode_flavor = klipper
high_current_on_filament_swap = 0
host_type = prusalink
inherits = 
layer_gcode = ;AFTER_LAYER_CHANGE\n;{layer_z}
machine_limits_usage = time_estimate_only
machine_max_acceleration_e = 6000
machine_max_acceleration_extruding = 6000
machine_max_acceleration_retracting = 12000
machine_max_acceleration_travel = 500
machine_max_acceleration_x = 6000
machine_max_acceleration_y = 6000
machine_max_acceleration_z = 500
machine_max_feedrate_e = 200
machine_max_feedrate_x = 1000
machine_max_feedrate_y = 1000
machine_max_feedrate_z = 10
machine_max_jerk_e = 0
machine_max_jerk_x = 0
machine_max_jerk_y = 0
machine_max_jerk_z = 0
machine_min_extruding_rate = 0
machine_min_travel_rate = 0
max_layer_height = 0.32
max_print_height = 295
min_layer_height = 0.06
multimaterial_purging = 140
nozzle_diameter = 0.4
nozzle_high_flow = 1
parking_pos_retraction = 92
pause_print_gcode = PAUSE
prefer_clockwise_movements = 0
print_host = 
printer_model = ENDER3V2
printer_notes = Do not remove the following keywords! These keywords are used in the "compatible printer" condition of the print and filament profiles to link the particular print and filament profiles to this printer profile.\nPRINTER_VENDOR_CREALITY\nPRINTER_MODEL_ENDER3V2\nPRINTER_HAS_BOWDEN
printer_settings_id = 
printer_technology = FFF
printer_variant = 0.4
printer_vendor = 
printhost_apikey = 
printhost_cafile = 
remaining_times = 0
retract_before_travel = 2
retract_before_wipe = 70%
retract_layer_change = 1
retract_length = 0.8
retract_length_toolchange = 1
retract_lift = 1
retract_lift_above = 0
retract_lift_below = 1
retract_restart_extra = 0
retract_restart_extra_toolchange = 0
retract_speed = 50
silent_mode = 0
single_extruder_multi_material = 0
start_gcode = M117\nSTART_PRINT EXTRUDER_TEMP={first_layer_temperature[initial_extruder]} BED_TEMP={first_layer_bed_temperature[initial_extruder]}
template_custom_gcode = 
thumbnails = 32x32/PNG, 300x300/PNG
thumbnails_format = PNG
toolchange_gcode = 
travel_lift_before_obstacle = 0
travel_max_lift = 0
travel_ramping_lift = 0
travel_slope = 0
use_firmware_retraction = 0
use_relative_e_distances = 0
use_volumetric_e = 0
variable_layer_height = 1
wipe = 1
z_offset = 0

[physical_printer:Mainsail]
host_type = moonraker
preset_name = Thesus
preset_names = Thesus
print_host = 10.0.100.111
printer_technology = FFF
printhost_apikey = 
printhost_authorization_type = key
printhost_cafile = 
printhost_password = 
printhost_port = 
printhost_ssl_ignore_revoke = 0
printhost_user = 

[presets]
print = 0.2mm height 0.4mm nozzle
sla_print = 
sla_material = 
printer = Thesus
filament = PLA
physical_printer = Mainsail