# generated by PrusaSlicer 2.9.2 on 2026-01-28 at 18:39:39 UTC

[print:0.18 Standard 0.6 + 0.6]
arc_fitting = disabled
automatic_extrusion_widths = 0
automatic_infill_combination = 0
automatic_infill_combination_max_layer_height = 100%
avoid_crossing_curled_overhangs = 0
avoid_crossing_perimeters = 1
avoid_crossing_perimeters_max_detour = 0
bed_temperature_extruder = 0
bottom_fill_pattern = monotonic
bottom_solid_layers = 3
bottom_solid_min_thickness = 0
bridge_acceleration = 1000
bridge_angle = 0
bridge_flow_ratio = 1
bridge_speed = 50
brim_separation = 0.1
brim_type = no_brim
brim_width = 5
compatible_printers = 
compatible_printers_condition = (printer_model=="Snapmaker A250" or printer_model=="Snapmaker A250 Dual" or printer_model=="Snapmaker A250 Dual QSKit" or printer_model=="Snapmaker A250 QSKit" or printer_model=="Snapmaker A350" or printer_model=="Snapmaker A350 Dual" or printer_model=="Snapmaker A350 Dual QSKit" or printer_model=="Snapmaker A350 QSKit") and (nozzle_diameter[0]=="0.6")
complete_objects = 0
default_acceleration = 2000
dont_support_bridges = 1
draft_shield = disabled
elefant_foot_compensation = 0.1
enable_dynamic_overhang_speeds = 1
ensure_vertical_shell_thickness = enabled
external_perimeter_acceleration = 1000
external_perimeter_extrusion_width = 0.62
external_perimeter_speed = 90
external_perimeters_first = 0
extra_perimeters = 1
extra_perimeters_on_overhangs = 0
extrusion_width = 0.62
fill_angle = 45
fill_density = 15%
fill_pattern = grid
first_layer_acceleration = 500
first_layer_acceleration_over_raft = 0
first_layer_extrusion_width = 0.62
first_layer_height = 0.2
first_layer_infill_speed = 0
first_layer_speed = 35
first_layer_speed_over_raft = 30
fuzzy_skin = none
fuzzy_skin_point_dist = 0.8
fuzzy_skin_thickness = 0.3
gap_fill_enabled = 0
gap_fill_speed = 50
gcode_comments = 0
gcode_label_objects = disabled
gcode_resolution = 0.0125
gcode_substitutions = 
infill_acceleration = 2000
infill_anchor = 600%
infill_anchor_max = 50
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0.62
infill_first = 0
infill_overlap = 25%
infill_speed = 100
inherits = 
interface_shells = 0
interlocking_beam = 0
interlocking_beam_layer_count = 2
interlocking_beam_width = 0.8
interlocking_boundary_avoidance = 2
interlocking_depth = 2
interlocking_orientation = 22.5
ironing = 0
ironing_flowrate = 10%
ironing_spacing = 0.15
ironing_speed = 30
ironing_type = top
layer_height = 0.18
max_print_speed = 100
max_volumetric_extrusion_rate_slope_negative = 0
max_volumetric_extrusion_rate_slope_positive = 0
max_volumetric_speed = 0
min_bead_width = 85%
min_feature_size = 25%
min_skirt_length = 0
mmu_segmented_region_interlocking_depth = 0
mmu_segmented_region_max_width = 0
notes = 
only_one_perimeter_first_layer = 0
only_retract_when_crossing_perimeters = 0
ooze_prevention = 1
output_filename_format = {input_filename_base}_{layer_height}mm_{print_time}.gcode
over_bridge_speed = 0
overhang_speed_0 = 10
overhang_speed_1 = 15
overhang_speed_2 = 50
overhang_speed_3 = 0
overhangs = 1
perimeter_acceleration = 2000
perimeter_extruder = 1
perimeter_extrusion_width = 0.62
perimeter_generator = arachne
perimeter_speed = 90
perimeters = 2
post_process = 
print_settings_id = 
raft_contact_distance = 0.1
raft_expansion = 2
raft_first_layer_density = 90%
raft_first_layer_expansion = 3
raft_layers = 0
resolution = 0.012
scarf_seam_entire_loop = 0
scarf_seam_length = 20
scarf_seam_max_segment_length = 1
scarf_seam_on_inner_perimeters = 0
scarf_seam_only_on_smooth = 1
scarf_seam_placement = nowhere
scarf_seam_start_height = 0%
seam_gap_distance = 15%
seam_position = aligned
single_extruder_multi_material_priming = 0
skirt_distance = 2
skirt_height = 1
skirts = 0
slice_closing_radius = 0.049
slicing_mode = regular
small_perimeter_speed = 15
solid_infill_acceleration = 2000
solid_infill_below_area = 70
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_width = 0.62
solid_infill_speed = 100
spiral_vase = 0
staggered_inner_seams = 0
standby_temperature_delta = -20
support_material = 1
support_material_angle = 0
support_material_auto = 1
support_material_bottom_contact_distance = 0.12
support_material_bottom_interface_layers = 3
support_material_buildplate_only = 0
support_material_closing_radius = 2
support_material_contact_distance = 0
support_material_enforce_layers = 0
support_material_extruder = 0
support_material_extrusion_width = 0.62
support_material_interface_contact_loops = 0
support_material_interface_extruder = 0
support_material_interface_layers = 2
support_material_interface_pattern = auto
support_material_interface_spacing = 0.12
support_material_interface_speed = 35
support_material_pattern = rectilinear
support_material_spacing = 2.5
support_material_speed = 100
support_material_style = organic
support_material_synchronize_layers = 0
support_material_threshold = 30
support_material_with_sheath = 1
support_material_xy_spacing = 50%
support_tree_angle = 40
support_tree_angle_slow = 25
support_tree_branch_diameter = 5
support_tree_branch_diameter_angle = 15
support_tree_branch_diameter_double_wall = 3
support_tree_branch_distance = 5
support_tree_tip_diameter = 0.8
support_tree_top_rate = 15%
thick_bridges = 1
thin_walls = 0
top_fill_pattern = monotonic
top_infill_extrusion_width = 0.62
top_one_perimeter_type = none
top_solid_infill_acceleration = 1000
top_solid_infill_speed = 100
top_solid_layers = 3
top_solid_min_thickness = 0.8
travel_acceleration = 2000
travel_speed = 120
travel_speed_z = 0
wall_distribution_count = 1
wall_transition_angle = 10
wall_transition_filter_deviation = 25%
wall_transition_length = 100%
wipe_tower = 1
wipe_tower_acceleration = 0
wipe_tower_bridging = 10
wipe_tower_brim_width = 5
wipe_tower_cone_angle = 40
wipe_tower_extra_flow = 100%
wipe_tower_extra_spacing = 100%
wipe_tower_extruder = 0
wipe_tower_no_sparse_layers = 0
wipe_tower_width = 30
xy_size_compensation = 0

[print:0.20mm SPEED @COREONE HF0.4 - Copy]
arc_fitting = emit_center
automatic_extrusion_widths = 0
automatic_infill_combination = 0
automatic_infill_combination_max_layer_height = 100%
avoid_crossing_curled_overhangs = 0
avoid_crossing_perimeters = 0
avoid_crossing_perimeters_max_detour = 0
bed_temperature_extruder = 0
bottom_fill_pattern = monotonic
bottom_solid_layers = 3
bottom_solid_min_thickness = 0.5
bridge_acceleration = 1500
bridge_angle = 0
bridge_flow_ratio = 1
bridge_speed = 50
brim_separation = 0.1
brim_type = outer_only
brim_width = 0
compatible_printers = 
compatible_printers_condition = printer_model=~/(COREONE|COREONEMMU3)/ and nozzle_diameter[0]==0.4 and nozzle_high_flow[0]
complete_objects = 0
default_acceleration = 3000
dont_support_bridges = 0
draft_shield = disabled
elefant_foot_compensation = 0.2
enable_dynamic_overhang_speeds = 1
ensure_vertical_shell_thickness = enabled
external_perimeter_acceleration = 3000
external_perimeter_extrusion_width = 0.45
external_perimeter_speed = 200
external_perimeters_first = 0
extra_perimeters = 0
extra_perimeters_on_overhangs = 0
extrusion_width = 0.45
fill_angle = 45
fill_density = 15%
fill_pattern = grid
first_layer_acceleration = 500
first_layer_acceleration_over_raft = 0
first_layer_extrusion_width = 0.5
first_layer_height = 0.2
first_layer_infill_speed = 0
first_layer_speed = 45
first_layer_speed_over_raft = 30
fuzzy_skin = none
fuzzy_skin_point_dist = 0.8
fuzzy_skin_thickness = 0.3
gap_fill_enabled = 1
gap_fill_speed = 120
gcode_comments = 0
gcode_label_objects = firmware
gcode_resolution = 0.008
gcode_substitutions = 
infill_acceleration = 7000
infill_anchor = 2
infill_anchor_max = 12
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0.45
infill_first = 0
infill_overlap = 15%
infill_speed = 300
inherits = 
interface_shells = 0
interlocking_beam = 0
interlocking_beam_layer_count = 2
interlocking_beam_width = 0.8
interlocking_boundary_avoidance = 2
interlocking_depth = 2
interlocking_orientation = 22.5
ironing = 0
ironing_flowrate = 15%
ironing_spacing = 0.1
ironing_speed = 15
ironing_type = top
layer_height = 0.2
max_print_speed = 300
max_volumetric_extrusion_rate_slope_negative = 0
max_volumetric_extrusion_rate_slope_positive = 0
max_volumetric_speed = 0
min_bead_width = 85%
min_feature_size = 25%
min_skirt_length = 4
mmu_segmented_region_interlocking_depth = 0
mmu_segmented_region_max_width = 0
notes = 
only_one_perimeter_first_layer = 0
only_retract_when_crossing_perimeters = 0
ooze_prevention = 0
output_filename_format = {input_filename_base}_0.4n_{layer_height}mm_{printing_filament_types}_{printer_model}_{print_time}.gcode
over_bridge_speed = 0
overhang_speed_0 = 15
overhang_speed_1 = 25
overhang_speed_2 = 50
overhang_speed_3 = 60%
overhangs = 1
perimeter_acceleration = 6000
perimeter_extruder = 1
perimeter_extrusion_width = 0.45
perimeter_generator = arachne
perimeter_speed = 250
perimeters = 2
post_process = 
print_settings_id = 
raft_contact_distance = 0.15
raft_expansion = 1.5
raft_first_layer_density = 80%
raft_first_layer_expansion = 3.5
raft_layers = 0
resolution = 0
scarf_seam_entire_loop = 0
scarf_seam_length = 20
scarf_seam_max_segment_length = 1
scarf_seam_on_inner_perimeters = 0
scarf_seam_only_on_smooth = 1
scarf_seam_placement = nowhere
scarf_seam_start_height = 0%
seam_gap_distance = 15%
seam_position = aligned
single_extruder_multi_material_priming = 0
skirt_distance = 6
skirt_height = 1
skirts = 0
slice_closing_radius = 0.049
slicing_mode = regular
small_perimeter_speed = 170
solid_infill_acceleration = 6000
solid_infill_below_area = 0
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_width = 0.45
solid_infill_speed = 250
spiral_vase = 0
staggered_inner_seams = 0
standby_temperature_delta = -5
support_material = 1
support_material_angle = 0
support_material_auto = 0
support_material_bottom_contact_distance = 0
support_material_bottom_interface_layers = 0
support_material_buildplate_only = 0
support_material_closing_radius = 2
support_material_contact_distance = 0.2
support_material_enforce_layers = 0
support_material_extruder = 0
support_material_extrusion_width = 0.36
support_material_interface_contact_loops = 0
support_material_interface_extruder = 0
support_material_interface_layers = 0
support_material_interface_pattern = auto
support_material_interface_spacing = 0.2
support_material_interface_speed = 50%
support_material_pattern = rectilinear
support_material_spacing = 2
support_material_speed = 120
support_material_style = organic
support_material_synchronize_layers = 0
support_material_threshold = 40
support_material_with_sheath = 0
support_material_xy_spacing = 80%
support_tree_angle = 40
support_tree_angle_slow = 25
support_tree_branch_diameter = 2
support_tree_branch_diameter_angle = 5
support_tree_branch_diameter_double_wall = 3
support_tree_branch_distance = 1
support_tree_tip_diameter = 0.8
support_tree_top_rate = 30%
thick_bridges = 0
thin_walls = 0
top_fill_pattern = monotoniclines
top_infill_extrusion_width = 0.42
top_one_perimeter_type = none
top_solid_infill_acceleration = 2000
top_solid_infill_speed = 100
top_solid_layers = 5
top_solid_min_thickness = 0.7
travel_acceleration = 7000
travel_speed = 350
travel_speed_z = 12
wall_distribution_count = 1
wall_transition_angle = 10
wall_transition_filter_deviation = 25%
wall_transition_length = 100%
wipe_tower = 1
wipe_tower_acceleration = 0
wipe_tower_bridging = 10
wipe_tower_brim_width = 2
wipe_tower_cone_angle = 25
wipe_tower_extra_flow = 250%
wipe_tower_extra_spacing = 110%
wipe_tower_extruder = 0
wipe_tower_no_sparse_layers = 0
wipe_tower_width = 60
xy_size_compensation = 0

[print:0.24 Standard @Snapmaker (0.6 nozzle) - Copy]
arc_fitting = disabled
automatic_extrusion_widths = 0
automatic_infill_combination = 0
automatic_infill_combination_max_layer_height = 100%
avoid_crossing_curled_overhangs = 0
avoid_crossing_perimeters = 1
avoid_crossing_perimeters_max_detour = 0
bed_temperature_extruder = 0
bottom_fill_pattern = monotonic
bottom_solid_layers = 3
bottom_solid_min_thickness = 0
bridge_acceleration = 1000
bridge_angle = 0
bridge_flow_ratio = 0.95
bridge_speed = 50
brim_separation = 0.1
brim_type = no_brim
brim_width = 5
compatible_printers = 
compatible_printers_condition = (printer_model=="Snapmaker A250" or printer_model=="Snapmaker A250 Dual" or printer_model=="Snapmaker A250 Dual QSKit" or printer_model=="Snapmaker A250 QSKit" or printer_model=="Snapmaker A350" or printer_model=="Snapmaker A350 Dual" or printer_model=="Snapmaker A350 Dual QSKit" or printer_model=="Snapmaker A350 QSKit") and (nozzle_diameter[0]=="0.6")
complete_objects = 0
default_acceleration = 2000
dont_support_bridges = 1
draft_shield = disabled
elefant_foot_compensation = 0.1
enable_dynamic_overhang_speeds = 1
ensure_vertical_shell_thickness = enabled
external_perimeter_acceleration = 1000
external_perimeter_extrusion_width = 0.62
external_perimeter_speed = 90
external_perimeters_first = 0
extra_perimeters = 1
extra_perimeters_on_overhangs = 0
extrusion_width = 0.62
fill_angle = 45
fill_density = 15%
fill_pattern = grid
first_layer_acceleration = 500
first_layer_acceleration_over_raft = 0
first_layer_extrusion_width = 0.62
first_layer_height = 0.3
first_layer_infill_speed = 0
first_layer_speed = 35
first_layer_speed_over_raft = 30
fuzzy_skin = none
fuzzy_skin_point_dist = 0.8
fuzzy_skin_thickness = 0.3
gap_fill_enabled = 0
gap_fill_speed = 50
gcode_comments = 0
gcode_label_objects = disabled
gcode_resolution = 0.0125
gcode_substitutions = 
infill_acceleration = 2000
infill_anchor = 600%
infill_anchor_max = 50
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0.62
infill_first = 0
infill_overlap = 25%
infill_speed = 100
inherits = 
interface_shells = 0
interlocking_beam = 0
interlocking_beam_layer_count = 2
interlocking_beam_width = 0.8
interlocking_boundary_avoidance = 2
interlocking_depth = 2
interlocking_orientation = 22.5
ironing = 0
ironing_flowrate = 10%
ironing_spacing = 0.15
ironing_speed = 30
ironing_type = top
layer_height = 0.24
max_print_speed = 80
max_volumetric_extrusion_rate_slope_negative = 0
max_volumetric_extrusion_rate_slope_positive = 0
max_volumetric_speed = 0
min_bead_width = 85%
min_feature_size = 25%
min_skirt_length = 0
mmu_segmented_region_interlocking_depth = 0
mmu_segmented_region_max_width = 0
notes = 
only_one_perimeter_first_layer = 0
only_retract_when_crossing_perimeters = 0
ooze_prevention = 0
output_filename_format = {input_filename_base}_{layer_height}mm_{print_time}.gcode
over_bridge_speed = 0
overhang_speed_0 = 10
overhang_speed_1 = 15
overhang_speed_2 = 50
overhang_speed_3 = 0
overhangs = 1
perimeter_acceleration = 2000
perimeter_extruder = 1
perimeter_extrusion_width = 0.62
perimeter_generator = arachne
perimeter_speed = 85
perimeters = 2
post_process = 
print_settings_id = 
raft_contact_distance = 0.1
raft_expansion = 2
raft_first_layer_density = 90%
raft_first_layer_expansion = 3
raft_layers = 0
resolution = 0.012
scarf_seam_entire_loop = 0
scarf_seam_length = 20
scarf_seam_max_segment_length = 1
scarf_seam_on_inner_perimeters = 0
scarf_seam_only_on_smooth = 1
scarf_seam_placement = nowhere
scarf_seam_start_height = 0%
seam_gap_distance = 15%
seam_position = aligned
single_extruder_multi_material_priming = 0
skirt_distance = 2
skirt_height = 1
skirts = 0
slice_closing_radius = 0.049
slicing_mode = regular
small_perimeter_speed = 15
solid_infill_acceleration = 2000
solid_infill_below_area = 70
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_width = 0.62
solid_infill_speed = 100
spiral_vase = 0
staggered_inner_seams = 0
standby_temperature_delta = -45
support_material = 1
support_material_angle = 0
support_material_auto = 0
support_material_bottom_contact_distance = 0.12
support_material_bottom_interface_layers = 3
support_material_buildplate_only = 1
support_material_closing_radius = 2
support_material_contact_distance = 0
support_material_enforce_layers = 0
support_material_extruder = 0
support_material_extrusion_width = 0.62
support_material_interface_contact_loops = 0
support_material_interface_extruder = 0
support_material_interface_layers = 2
support_material_interface_pattern = auto
support_material_interface_spacing = 0.12
support_material_interface_speed = 35
support_material_pattern = rectilinear
support_material_spacing = 2.5
support_material_speed = 100
support_material_style = organic
support_material_synchronize_layers = 0
support_material_threshold = 30
support_material_with_sheath = 1
support_material_xy_spacing = 50%
support_tree_angle = 40
support_tree_angle_slow = 25
support_tree_branch_diameter = 5
support_tree_branch_diameter_angle = 15
support_tree_branch_diameter_double_wall = 3
support_tree_branch_distance = 5
support_tree_tip_diameter = 0.8
support_tree_top_rate = 15%
thick_bridges = 1
thin_walls = 0
top_fill_pattern = monotonic
top_infill_extrusion_width = 0.62
top_one_perimeter_type = none
top_solid_infill_acceleration = 1000
top_solid_infill_speed = 100
top_solid_layers = 3
top_solid_min_thickness = 0.8
travel_acceleration = 2000
travel_speed = 120
travel_speed_z = 0
wall_distribution_count = 1
wall_transition_angle = 10
wall_transition_filter_deviation = 25%
wall_transition_length = 100%
wipe_tower = 0
wipe_tower_acceleration = 0
wipe_tower_bridging = 10
wipe_tower_brim_width = 5
wipe_tower_cone_angle = 40
wipe_tower_extra_flow = 100%
wipe_tower_extra_spacing = 100%
wipe_tower_extruder = 0
wipe_tower_no_sparse_layers = 0
wipe_tower_width = 25
xy_size_compensation = 0

[print:0.24mm 0.4 nozzle SPEED - Ender3V2PS]
arc_fitting = disabled
automatic_extrusion_widths = 1
automatic_infill_combination = 0
automatic_infill_combination_max_layer_height = 100%
avoid_crossing_curled_overhangs = 0
avoid_crossing_perimeters = 0
avoid_crossing_perimeters_max_detour = 0
bed_temperature_extruder = 0
bottom_fill_pattern = rectilinear
bottom_solid_layers = 4
bottom_solid_min_thickness = 0
bridge_acceleration = 0
bridge_angle = 0
bridge_flow_ratio = 0.95
bridge_speed = 60
brim_separation = 0
brim_type = outer_only
brim_width = 0
compatible_printers = 
compatible_printers_condition = printer_model=~/(ENDER|CR|SERMOON).*/ and nozzle_diameter[0]==0.4
complete_objects = 0
default_acceleration = 0
dont_support_bridges = 1
draft_shield = disabled
elefant_foot_compensation = 0.3
enable_dynamic_overhang_speeds = 0
ensure_vertical_shell_thickness = enabled
external_perimeter_acceleration = 0
external_perimeter_extrusion_width = 0
external_perimeter_speed = 140
external_perimeters_first = 1
extra_perimeters = 0
extra_perimeters_on_overhangs = 0
extrusion_width = 0
fill_angle = 45
fill_density = 20%
fill_pattern = rectilinear
first_layer_acceleration = 0
first_layer_acceleration_over_raft = 0
first_layer_extrusion_width = 0
first_layer_height = 0.15
first_layer_infill_speed = 0
first_layer_speed = 20%
first_layer_speed_over_raft = 30
fuzzy_skin = none
fuzzy_skin_point_dist = 0.8
fuzzy_skin_thickness = 0.3
gap_fill_enabled = 1
gap_fill_speed = 60
gcode_comments = 0
gcode_label_objects = firmware
gcode_resolution = 0.0125
gcode_substitutions = 
infill_acceleration = 0
infill_anchor = 600%
infill_anchor_max = 50
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0
infill_first = 0
infill_overlap = 0
infill_speed = 200
inherits = 
interface_shells = 0
interlocking_beam = 0
interlocking_beam_layer_count = 2
interlocking_beam_width = 0.8
interlocking_boundary_avoidance = 2
interlocking_depth = 2
interlocking_orientation = 22.5
ironing = 0
ironing_flowrate = 15%
ironing_spacing = 0.1
ironing_speed = 15
ironing_type = top
layer_height = 0.2
max_print_speed = 180
max_volumetric_extrusion_rate_slope_negative = 0
max_volumetric_extrusion_rate_slope_positive = 0
max_volumetric_speed = 0
min_bead_width = 85%
min_feature_size = 25%
min_skirt_length = 4
mmu_segmented_region_interlocking_depth = 0
mmu_segmented_region_max_width = 0
notes = 
only_one_perimeter_first_layer = 0
only_retract_when_crossing_perimeters = 0
ooze_prevention = 0
output_filename_format = {input_filename_base}_{printer_model}.gcode
over_bridge_speed = 0
overhang_speed_0 = 15
overhang_speed_1 = 15
overhang_speed_2 = 20
overhang_speed_3 = 25
overhangs = 1
perimeter_acceleration = 0
perimeter_extruder = 1
perimeter_extrusion_width = 0
perimeter_generator = arachne
perimeter_speed = 160
perimeters = 3
post_process = 
print_settings_id = 
raft_contact_distance = 0.1
raft_expansion = 1.5
raft_first_layer_density = 90%
raft_first_layer_expansion = 3
raft_layers = 0
resolution = 0
scarf_seam_entire_loop = 0
scarf_seam_length = 20
scarf_seam_max_segment_length = 1
scarf_seam_on_inner_perimeters = 0
scarf_seam_only_on_smooth = 1
scarf_seam_placement = nowhere
scarf_seam_start_height = 0%
seam_gap_distance = 15%
seam_position = aligned
single_extruder_multi_material_priming = 0
skirt_distance = 3
skirt_height = 2
skirts = 0
slice_closing_radius = 0.049
slicing_mode = regular
small_perimeter_speed = 50%
solid_infill_acceleration = 0
solid_infill_below_area = 0
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_width = 0
solid_infill_speed = 140
spiral_vase = 0
staggered_inner_seams = 0
standby_temperature_delta = -5
support_material = 1
support_material_angle = 0
support_material_auto = 0
support_material_bottom_contact_distance = 0
support_material_bottom_interface_layers = -1
support_material_buildplate_only = 0
support_material_closing_radius = 2
support_material_contact_distance = 0.15
support_material_enforce_layers = 0
support_material_extruder = 0
support_material_extrusion_width = 0
support_material_interface_contact_loops = 0
support_material_interface_extruder = 0
support_material_interface_layers = 0
support_material_interface_pattern = auto
support_material_interface_spacing = 0.2
support_material_interface_speed = 100%
support_material_pattern = honeycomb
support_material_spacing = 1
support_material_speed = 60
support_material_style = organic
support_material_synchronize_layers = 0
support_material_threshold = 40
support_material_with_sheath = 0
support_material_xy_spacing = 80%
support_tree_angle = 40
support_tree_angle_slow = 25
support_tree_branch_diameter = 2
support_tree_branch_diameter_angle = 5
support_tree_branch_diameter_double_wall = 3
support_tree_branch_distance = 1
support_tree_tip_diameter = 0.8
support_tree_top_rate = 30%
thick_bridges = 1
thin_walls = 1
top_fill_pattern = rectilinear
top_infill_extrusion_width = 0
top_one_perimeter_type = none
top_solid_infill_acceleration = 0
top_solid_infill_speed = 100
top_solid_layers = 4
top_solid_min_thickness = 0
travel_acceleration = 0
travel_speed = 220
travel_speed_z = 0
wall_distribution_count = 1
wall_transition_angle = 10
wall_transition_filter_deviation = 25%
wall_transition_length = 100%
wipe_tower = 0
wipe_tower_acceleration = 0
wipe_tower_bridging = 10
wipe_tower_brim_width = 2
wipe_tower_cone_angle = 0
wipe_tower_extra_flow = 100%
wipe_tower_extra_spacing = 100%
wipe_tower_extruder = 0
wipe_tower_no_sparse_layers = 0
wipe_tower_width = 60
xy_size_compensation = 0

[print:0.2mm Standard 0.6 + 0.6]
arc_fitting = disabled
automatic_extrusion_widths = 0
automatic_infill_combination = 0
automatic_infill_combination_max_layer_height = 100%
avoid_crossing_curled_overhangs = 0
avoid_crossing_perimeters = 1
avoid_crossing_perimeters_max_detour = 0
bed_temperature_extruder = 0
bottom_fill_pattern = monotonic
bottom_solid_layers = 3
bottom_solid_min_thickness = 0
bridge_acceleration = 3500
bridge_angle = 0
bridge_flow_ratio = 1
bridge_speed = 60
brim_separation = 0.1
brim_type = no_brim
brim_width = 5
compatible_printers = 
compatible_printers_condition = (printer_model=="Snapmaker A250" or printer_model=="Snapmaker A250 Dual" or printer_model=="Snapmaker A250 Dual QSKit" or printer_model=="Snapmaker A250 QSKit" or printer_model=="Snapmaker A350" or printer_model=="Snapmaker A350 Dual" or printer_model=="Snapmaker A350 Dual QSKit" or printer_model=="Snapmaker A350 QSKit") and (nozzle_diameter[0]=="0.6")
complete_objects = 0
default_acceleration = 3500
dont_support_bridges = 1
draft_shield = disabled
elefant_foot_compensation = 0.1
enable_dynamic_overhang_speeds = 0
ensure_vertical_shell_thickness = enabled
external_perimeter_acceleration = 3500
external_perimeter_extrusion_width = 0
external_perimeter_speed = 100
external_perimeters_first = 0
extra_perimeters = 1
extra_perimeters_on_overhangs = 0
extrusion_width = 0
fill_angle = 45
fill_density = 10%
fill_pattern = grid
first_layer_acceleration = 3500
first_layer_acceleration_over_raft = 0
first_layer_extrusion_width = 0
first_layer_height = 0.2
first_layer_infill_speed = 0
first_layer_speed = 50
first_layer_speed_over_raft = 30
fuzzy_skin = none
fuzzy_skin_point_dist = 0.8
fuzzy_skin_thickness = 0.3
gap_fill_enabled = 0
gap_fill_speed = 60
gcode_comments = 0
gcode_label_objects = disabled
gcode_resolution = 0.0125
gcode_substitutions = 
infill_acceleration = 3500
infill_anchor = 600%
infill_anchor_max = 50
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0
infill_first = 0
infill_overlap = 25%
infill_speed = 120
inherits = 
interface_shells = 0
interlocking_beam = 0
interlocking_beam_layer_count = 2
interlocking_beam_width = 0.8
interlocking_boundary_avoidance = 2
interlocking_depth = 2
interlocking_orientation = 22.5
ironing = 0
ironing_flowrate = 10%
ironing_spacing = 0.15
ironing_speed = 30
ironing_type = top
layer_height = 0.2
max_print_speed = 150
max_volumetric_extrusion_rate_slope_negative = 0
max_volumetric_extrusion_rate_slope_positive = 0
max_volumetric_speed = 0
min_bead_width = 85%
min_feature_size = 25%
min_skirt_length = 0
mmu_segmented_region_interlocking_depth = 0
mmu_segmented_region_max_width = 0
notes = 
only_one_perimeter_first_layer = 0
only_retract_when_crossing_perimeters = 0
ooze_prevention = 1
output_filename_format = {input_filename_base}_SNAPDEX.gcode
over_bridge_speed = 0
overhang_speed_0 = 100%
overhang_speed_1 = 100%
overhang_speed_2 = 100%
overhang_speed_3 = 100%
overhangs = 1
perimeter_acceleration = 3500
perimeter_extruder = 1
perimeter_extrusion_width = 0
perimeter_generator = arachne
perimeter_speed = 100
perimeters = 2
post_process = 
print_settings_id = 
raft_contact_distance = 0.1
raft_expansion = 2
raft_first_layer_density = 90%
raft_first_layer_expansion = 3
raft_layers = 0
resolution = 0.012
scarf_seam_entire_loop = 0
scarf_seam_length = 20
scarf_seam_max_segment_length = 1
scarf_seam_on_inner_perimeters = 0
scarf_seam_only_on_smooth = 1
scarf_seam_placement = nowhere
scarf_seam_start_height = 0%
seam_gap_distance = 15%
seam_position = aligned
single_extruder_multi_material_priming = 0
skirt_distance = 2
skirt_height = 1
skirts = 0
slice_closing_radius = 0.049
slicing_mode = regular
small_perimeter_speed = 80
solid_infill_acceleration = 3500
solid_infill_below_area = 70
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_width = 0
solid_infill_speed = 100
spiral_vase = 0
staggered_inner_seams = 0
standby_temperature_delta = -20
support_material = 0
support_material_angle = 0
support_material_auto = 1
support_material_bottom_contact_distance = 0.12
support_material_bottom_interface_layers = 3
support_material_buildplate_only = 0
support_material_closing_radius = 2
support_material_contact_distance = 0.2
support_material_enforce_layers = 0
support_material_extruder = 0
support_material_extrusion_width = 0.62
support_material_interface_contact_loops = 0
support_material_interface_extruder = 0
support_material_interface_layers = 2
support_material_interface_pattern = auto
support_material_interface_spacing = 0.12
support_material_interface_speed = 60
support_material_pattern = rectilinear
support_material_spacing = 2.5
support_material_speed = 100
support_material_style = organic
support_material_synchronize_layers = 1
support_material_threshold = 30
support_material_with_sheath = 1
support_material_xy_spacing = 50%
support_tree_angle = 40
support_tree_angle_slow = 25
support_tree_branch_diameter = 5
support_tree_branch_diameter_angle = 15
support_tree_branch_diameter_double_wall = 3
support_tree_branch_distance = 5
support_tree_tip_diameter = 0.8
support_tree_top_rate = 15%
thick_bridges = 1
thin_walls = 0
top_fill_pattern = monotonic
top_infill_extrusion_width = 0
top_one_perimeter_type = none
top_solid_infill_acceleration = 3500
top_solid_infill_speed = 100
top_solid_layers = 3
top_solid_min_thickness = 0.8
travel_acceleration = 5000
travel_speed = 125
travel_speed_z = 30
wall_distribution_count = 1
wall_transition_angle = 10
wall_transition_filter_deviation = 25%
wall_transition_length = 100%
wipe_tower = 0
wipe_tower_acceleration = 3500
wipe_tower_bridging = 10
wipe_tower_brim_width = 5
wipe_tower_cone_angle = 40
wipe_tower_extra_flow = 100%
wipe_tower_extra_spacing = 100%
wipe_tower_extruder = 0
wipe_tower_no_sparse_layers = 0
wipe_tower_width = 30
xy_size_compensation = 0

[print:0.30 Standard @Snapmaker (0.6 nozzle) - Copy]
arc_fitting = disabled
automatic_extrusion_widths = 0
automatic_infill_combination = 0
automatic_infill_combination_max_layer_height = 100%
avoid_crossing_curled_overhangs = 0
avoid_crossing_perimeters = 1
avoid_crossing_perimeters_max_detour = 0
bed_temperature_extruder = 0
bottom_fill_pattern = monotonic
bottom_solid_layers = 3
bottom_solid_min_thickness = 0
bridge_acceleration = 1000
bridge_angle = 0
bridge_flow_ratio = 0.95
bridge_speed = 30
brim_separation = 0.1
brim_type = no_brim
brim_width = 5
compatible_printers = 
compatible_printers_condition = (printer_model=="Snapmaker A250" or printer_model=="Snapmaker A250 Dual" or printer_model=="Snapmaker A250 Dual QSKit" or printer_model=="Snapmaker A250 QSKit" or printer_model=="Snapmaker A350" or printer_model=="Snapmaker A350 Dual" or printer_model=="Snapmaker A350 Dual QSKit" or printer_model=="Snapmaker A350 QSKit") and (nozzle_diameter[0]=="0.6")
complete_objects = 0
default_acceleration = 2000
dont_support_bridges = 1
draft_shield = disabled
elefant_foot_compensation = 0.1
enable_dynamic_overhang_speeds = 1
ensure_vertical_shell_thickness = enabled
external_perimeter_acceleration = 1000
external_perimeter_extrusion_width = 0.62
external_perimeter_speed = 75
external_perimeters_first = 0
extra_perimeters = 1
extra_perimeters_on_overhangs = 0
extrusion_width = 0.62
fill_angle = 45
fill_density = 20%
fill_pattern = grid
first_layer_acceleration = 500
first_layer_acceleration_over_raft = 0
first_layer_extrusion_width = 0.62
first_layer_height = 0.3
first_layer_infill_speed = 0
first_layer_speed = 35
first_layer_speed_over_raft = 30
fuzzy_skin = none
fuzzy_skin_point_dist = 0.8
fuzzy_skin_thickness = 0.3
gap_fill_enabled = 0
gap_fill_speed = 50
gcode_comments = 0
gcode_label_objects = disabled
gcode_resolution = 0.0125
gcode_substitutions = 
infill_acceleration = 2000
infill_anchor = 600%
infill_anchor_max = 50
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0.62
infill_first = 0
infill_overlap = 25%
infill_speed = 100
inherits = 
interface_shells = 0
interlocking_beam = 0
interlocking_beam_layer_count = 2
interlocking_beam_width = 0.8
interlocking_boundary_avoidance = 2
interlocking_depth = 2
interlocking_orientation = 22.5
ironing = 0
ironing_flowrate = 10%
ironing_spacing = 0.15
ironing_speed = 30
ironing_type = top
layer_height = 0.3
max_print_speed = 80
max_volumetric_extrusion_rate_slope_negative = 0
max_volumetric_extrusion_rate_slope_positive = 0
max_volumetric_speed = 0
min_bead_width = 85%
min_feature_size = 25%
min_skirt_length = 0
mmu_segmented_region_interlocking_depth = 0
mmu_segmented_region_max_width = 0
notes = 
only_one_perimeter_first_layer = 0
only_retract_when_crossing_perimeters = 0
ooze_prevention = 0
output_filename_format = {input_filename_base}_{layer_height}mm_{print_time}.gcode
over_bridge_speed = 0
overhang_speed_0 = 10
overhang_speed_1 = 15
overhang_speed_2 = 50
overhang_speed_3 = 0
overhangs = 1
perimeter_acceleration = 2000
perimeter_extruder = 1
perimeter_extrusion_width = 0.62
perimeter_generator = arachne
perimeter_speed = 85
perimeters = 3
post_process = 
print_settings_id = 
raft_contact_distance = 0.1
raft_expansion = 2
raft_first_layer_density = 90%
raft_first_layer_expansion = 3
raft_layers = 0
resolution = 0.012
scarf_seam_entire_loop = 0
scarf_seam_length = 20
scarf_seam_max_segment_length = 1
scarf_seam_on_inner_perimeters = 0
scarf_seam_only_on_smooth = 1
scarf_seam_placement = nowhere
scarf_seam_start_height = 0%
seam_gap_distance = 15%
seam_position = aligned
single_extruder_multi_material_priming = 0
skirt_distance = 2
skirt_height = 1
skirts = 0
slice_closing_radius = 0.049
slicing_mode = regular
small_perimeter_speed = 15
solid_infill_acceleration = 2000
solid_infill_below_area = 70
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_width = 0.62
solid_infill_speed = 85
spiral_vase = 0
staggered_inner_seams = 0
standby_temperature_delta = -45
support_material = 1
support_material_angle = 0
support_material_auto = 0
support_material_bottom_contact_distance = 0.12
support_material_bottom_interface_layers = 3
support_material_buildplate_only = 0
support_material_closing_radius = 2
support_material_contact_distance = 0
support_material_enforce_layers = 0
support_material_extruder = 0
support_material_extrusion_width = 0.62
support_material_interface_contact_loops = 0
support_material_interface_extruder = 0
support_material_interface_layers = 2
support_material_interface_pattern = auto
support_material_interface_spacing = 0.12
support_material_interface_speed = 35
support_material_pattern = rectilinear
support_material_spacing = 2.5
support_material_speed = 100
support_material_style = snug
support_material_synchronize_layers = 0
support_material_threshold = 30
support_material_with_sheath = 1
support_material_xy_spacing = 50%
support_tree_angle = 40
support_tree_angle_slow = 25
support_tree_branch_diameter = 5
support_tree_branch_diameter_angle = 15
support_tree_branch_diameter_double_wall = 3
support_tree_branch_distance = 5
support_tree_tip_diameter = 0.8
support_tree_top_rate = 15%
thick_bridges = 1
thin_walls = 0
top_fill_pattern = monotonic
top_infill_extrusion_width = 0.62
top_one_perimeter_type = none
top_solid_infill_acceleration = 1000
top_solid_infill_speed = 100
top_solid_layers = 3
top_solid_min_thickness = 0.8
travel_acceleration = 2000
travel_speed = 120
travel_speed_z = 0
wall_distribution_count = 1
wall_transition_angle = 10
wall_transition_filter_deviation = 25%
wall_transition_length = 100%
wipe_tower = 0
wipe_tower_acceleration = 0
wipe_tower_bridging = 10
wipe_tower_brim_width = 5
wipe_tower_cone_angle = 40
wipe_tower_extra_flow = 100%
wipe_tower_extra_spacing = 100%
wipe_tower_extruder = 0
wipe_tower_no_sparse_layers = 0
wipe_tower_width = 25
xy_size_compensation = 0

[print:100lamps]
arc_fitting = disabled
automatic_extrusion_widths = 1
automatic_infill_combination = 0
automatic_infill_combination_max_layer_height = 100%
avoid_crossing_curled_overhangs = 0
avoid_crossing_perimeters = 0
avoid_crossing_perimeters_max_detour = 0
bed_temperature_extruder = 0
bottom_fill_pattern = rectilinear
bottom_solid_layers = 4
bottom_solid_min_thickness = 0
bridge_acceleration = 0
bridge_angle = 0
bridge_flow_ratio = 0.95
bridge_speed = 60
brim_separation = 0
brim_type = outer_only
brim_width = 0
compatible_printers = 
compatible_printers_condition = printer_model=~/(ENDER|CR|SERMOON).*/ and nozzle_diameter[0]==0.4
complete_objects = 0
default_acceleration = 0
dont_support_bridges = 1
draft_shield = disabled
elefant_foot_compensation = 0.3
enable_dynamic_overhang_speeds = 0
ensure_vertical_shell_thickness = enabled
external_perimeter_acceleration = 0
external_perimeter_extrusion_width = 0
external_perimeter_speed = 140
external_perimeters_first = 1
extra_perimeters = 0
extra_perimeters_on_overhangs = 0
extrusion_width = 0
fill_angle = 45
fill_density = 0%
fill_pattern = rectilinear
first_layer_acceleration = 0
first_layer_acceleration_over_raft = 0
first_layer_extrusion_width = 0
first_layer_height = 0.2
first_layer_infill_speed = 0
first_layer_speed = 40%
first_layer_speed_over_raft = 30
fuzzy_skin = none
fuzzy_skin_point_dist = 0.8
fuzzy_skin_thickness = 0.3
gap_fill_enabled = 1
gap_fill_speed = 60
gcode_comments = 0
gcode_label_objects = firmware
gcode_resolution = 0.0125
gcode_substitutions = 
infill_acceleration = 0
infill_anchor = 600%
infill_anchor_max = 50
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0
infill_first = 0
infill_overlap = 0
infill_speed = 200
inherits = 
interface_shells = 0
interlocking_beam = 0
interlocking_beam_layer_count = 2
interlocking_beam_width = 0.8
interlocking_boundary_avoidance = 2
interlocking_depth = 2
interlocking_orientation = 22.5
ironing = 0
ironing_flowrate = 15%
ironing_spacing = 0.1
ironing_speed = 15
ironing_type = top
layer_height = 0.15
max_print_speed = 180
max_volumetric_extrusion_rate_slope_negative = 0
max_volumetric_extrusion_rate_slope_positive = 0
max_volumetric_speed = 0
min_bead_width = 85%
min_feature_size = 25%
min_skirt_length = 4
mmu_segmented_region_interlocking_depth = 0
mmu_segmented_region_max_width = 0
notes = 
only_one_perimeter_first_layer = 0
only_retract_when_crossing_perimeters = 0
ooze_prevention = 0
output_filename_format = {input_filename_base}_{printer_model}.gcode
over_bridge_speed = 0
overhang_speed_0 = 15
overhang_speed_1 = 15
overhang_speed_2 = 20
overhang_speed_3 = 25
overhangs = 1
perimeter_acceleration = 0
perimeter_extruder = 1
perimeter_extrusion_width = 0
perimeter_generator = arachne
perimeter_speed = 160
perimeters = 1
post_process = 
print_settings_id = 
raft_contact_distance = 0.1
raft_expansion = 1.5
raft_first_layer_density = 90%
raft_first_layer_expansion = 3
raft_layers = 0
resolution = 0
scarf_seam_entire_loop = 0
scarf_seam_length = 20
scarf_seam_max_segment_length = 1
scarf_seam_on_inner_perimeters = 0
scarf_seam_only_on_smooth = 1
scarf_seam_placement = nowhere
scarf_seam_start_height = 0%
seam_gap_distance = 15%
seam_position = aligned
single_extruder_multi_material_priming = 0
skirt_distance = 3
skirt_height = 2
skirts = 0
slice_closing_radius = 0.049
slicing_mode = regular
small_perimeter_speed = 50%
solid_infill_acceleration = 0
solid_infill_below_area = 0
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_width = 0
solid_infill_speed = 140
spiral_vase = 1
staggered_inner_seams = 0
standby_temperature_delta = -5
support_material = 0
support_material_angle = 0
support_material_auto = 0
support_material_bottom_contact_distance = 0
support_material_bottom_interface_layers = -1
support_material_buildplate_only = 0
support_material_closing_radius = 2
support_material_contact_distance = 0.15
support_material_enforce_layers = 0
support_material_extruder = 0
support_material_extrusion_width = 0
support_material_interface_contact_loops = 0
support_material_interface_extruder = 0
support_material_interface_layers = 0
support_material_interface_pattern = auto
support_material_interface_spacing = 0.2
support_material_interface_speed = 100%
support_material_pattern = honeycomb
support_material_spacing = 1
support_material_speed = 60
support_material_style = organic
support_material_synchronize_layers = 0
support_material_threshold = 40
support_material_with_sheath = 0
support_material_xy_spacing = 80%
support_tree_angle = 40
support_tree_angle_slow = 25
support_tree_branch_diameter = 2
support_tree_branch_diameter_angle = 5
support_tree_branch_diameter_double_wall = 3
support_tree_branch_distance = 1
support_tree_tip_diameter = 0.8
support_tree_top_rate = 30%
thick_bridges = 1
thin_walls = 0
top_fill_pattern = rectilinear
top_infill_extrusion_width = 0
top_one_perimeter_type = none
top_solid_infill_acceleration = 0
top_solid_infill_speed = 100
top_solid_layers = 0
top_solid_min_thickness = 0
travel_acceleration = 0
travel_speed = 220
travel_speed_z = 0
wall_distribution_count = 1
wall_transition_angle = 10
wall_transition_filter_deviation = 25%
wall_transition_length = 100%
wipe_tower = 0
wipe_tower_acceleration = 0
wipe_tower_bridging = 10
wipe_tower_brim_width = 2
wipe_tower_cone_angle = 0
wipe_tower_extra_flow = 100%
wipe_tower_extra_spacing = 100%
wipe_tower_extruder = 0
wipe_tower_no_sparse_layers = 0
wipe_tower_width = 60
xy_size_compensation = 0

[print:beeg plotter]
arc_fitting = disabled
automatic_extrusion_widths = 0
automatic_infill_combination = 0
automatic_infill_combination_max_layer_height = 100%
avoid_crossing_curled_overhangs = 0
avoid_crossing_perimeters = 0
avoid_crossing_perimeters_max_detour = 0
bed_temperature_extruder = 0
bottom_fill_pattern = rectilinear
bottom_solid_layers = 4
bottom_solid_min_thickness = 0
bridge_acceleration = 0
bridge_angle = 0
bridge_flow_ratio = 0.95
bridge_speed = 60
brim_separation = 0
brim_type = outer_only
brim_width = 0
compatible_printers = 
compatible_printers_condition = printer_model=~/(ENDER|CR|SERMOON).*/ and nozzle_diameter[0]==0.4
complete_objects = 0
default_acceleration = 0
dont_support_bridges = 1
draft_shield = disabled
elefant_foot_compensation = 0.3
enable_dynamic_overhang_speeds = 0
ensure_vertical_shell_thickness = enabled
external_perimeter_acceleration = 0
external_perimeter_extrusion_width = 0.2
external_perimeter_speed = 120
external_perimeters_first = 1
extra_perimeters = 0
extra_perimeters_on_overhangs = 0
extrusion_width = 0.2
fill_angle = 45
fill_density = 20%
fill_pattern = rectilinear
first_layer_acceleration = 0
first_layer_acceleration_over_raft = 0
first_layer_extrusion_width = 0.2
first_layer_height = 0.15
first_layer_infill_speed = 0
first_layer_speed = 20%
first_layer_speed_over_raft = 30
fuzzy_skin = none
fuzzy_skin_point_dist = 0.8
fuzzy_skin_thickness = 0.3
gap_fill_enabled = 1
gap_fill_speed = 60
gcode_comments = 0
gcode_label_objects = firmware
gcode_resolution = 0.0125
gcode_substitutions = 
infill_acceleration = 0
infill_anchor = 600%
infill_anchor_max = 50
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0
infill_first = 0
infill_overlap = 0
infill_speed = 120
inherits = 
interface_shells = 0
interlocking_beam = 0
interlocking_beam_layer_count = 2
interlocking_beam_width = 0.8
interlocking_boundary_avoidance = 2
interlocking_depth = 2
interlocking_orientation = 22.5
ironing = 0
ironing_flowrate = 15%
ironing_spacing = 0.1
ironing_speed = 15
ironing_type = top
layer_height = 0.1
max_print_speed = 120
max_volumetric_extrusion_rate_slope_negative = 0
max_volumetric_extrusion_rate_slope_positive = 0
max_volumetric_speed = 0
min_bead_width = 85%
min_feature_size = 25%
min_skirt_length = 4
mmu_segmented_region_interlocking_depth = 0
mmu_segmented_region_max_width = 0
notes = 
only_one_perimeter_first_layer = 0
only_retract_when_crossing_perimeters = 0
ooze_prevention = 0
output_filename_format = {input_filename_base}_{printer_model}.gcode
over_bridge_speed = 0
overhang_speed_0 = 15
overhang_speed_1 = 15
overhang_speed_2 = 20
overhang_speed_3 = 25
overhangs = 1
perimeter_acceleration = 0
perimeter_extruder = 1
perimeter_extrusion_width = 0.2
perimeter_generator = arachne
perimeter_speed = 120
perimeters = 3
post_process = 
print_settings_id = 
raft_contact_distance = 0.1
raft_expansion = 1.5
raft_first_layer_density = 90%
raft_first_layer_expansion = 3
raft_layers = 0
resolution = 0
scarf_seam_entire_loop = 0
scarf_seam_length = 20
scarf_seam_max_segment_length = 1
scarf_seam_on_inner_perimeters = 0
scarf_seam_only_on_smooth = 1
scarf_seam_placement = nowhere
scarf_seam_start_height = 0%
seam_gap_distance = 15%
seam_position = aligned
single_extruder_multi_material_priming = 0
skirt_distance = 3
skirt_height = 2
skirts = 0
slice_closing_radius = 0.049
slicing_mode = regular
small_perimeter_speed = 100%
solid_infill_acceleration = 0
solid_infill_below_area = 0
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_width = 0
solid_infill_speed = 120
spiral_vase = 0
staggered_inner_seams = 0
standby_temperature_delta = -5
support_material = 1
support_material_angle = 0
support_material_auto = 0
support_material_bottom_contact_distance = 0
support_material_bottom_interface_layers = -1
support_material_buildplate_only = 0
support_material_closing_radius = 2
support_material_contact_distance = 0.15
support_material_enforce_layers = 0
support_material_extruder = 0
support_material_extrusion_width = 0
support_material_interface_contact_loops = 0
support_material_interface_extruder = 0
support_material_interface_layers = 0
support_material_interface_pattern = auto
support_material_interface_spacing = 0.2
support_material_interface_speed = 100%
support_material_pattern = honeycomb
support_material_spacing = 1
support_material_speed = 60
support_material_style = organic
support_material_synchronize_layers = 0
support_material_threshold = 40
support_material_with_sheath = 0
support_material_xy_spacing = 80%
support_tree_angle = 40
support_tree_angle_slow = 25
support_tree_branch_diameter = 2
support_tree_branch_diameter_angle = 5
support_tree_branch_diameter_double_wall = 3
support_tree_branch_distance = 1
support_tree_tip_diameter = 0.8
support_tree_top_rate = 30%
thick_bridges = 1
thin_walls = 1
top_fill_pattern = rectilinear
top_infill_extrusion_width = 0
top_one_perimeter_type = none
top_solid_infill_acceleration = 0
top_solid_infill_speed = 120
top_solid_layers = 4
top_solid_min_thickness = 0
travel_acceleration = 0
travel_speed = 120
travel_speed_z = 0
wall_distribution_count = 1
wall_transition_angle = 10
wall_transition_filter_deviation = 25%
wall_transition_length = 100%
wipe_tower = 0
wipe_tower_acceleration = 0
wipe_tower_bridging = 10
wipe_tower_brim_width = 2
wipe_tower_cone_angle = 0
wipe_tower_extra_flow = 100%
wipe_tower_extra_spacing = 100%
wipe_tower_extruder = 0
wipe_tower_no_sparse_layers = 0
wipe_tower_width = 60
xy_size_compensation = 0

[print:beeg2_ava.ini (Beeg)]
arc_fitting = disabled
automatic_extrusion_widths = 0
automatic_infill_combination = 0
automatic_infill_combination_max_layer_height = 100%
avoid_crossing_curled_overhangs = 0
avoid_crossing_perimeters = 0
avoid_crossing_perimeters_max_detour = 0
bed_temperature_extruder = 0
bottom_fill_pattern = rectilinear
bottom_solid_layers = 1
bottom_solid_min_thickness = 0
bridge_acceleration = 0
bridge_angle = 0
bridge_flow_ratio = 1
bridge_speed = 60
brim_separation = 0
brim_type = outer_only
brim_width = 0
compatible_printers = 
compatible_printers_condition = 
complete_objects = 0
default_acceleration = 0
dont_support_bridges = 1
draft_shield = disabled
elefant_foot_compensation = 0
enable_dynamic_overhang_speeds = 0
ensure_vertical_shell_thickness = enabled
external_perimeter_acceleration = 0
external_perimeter_extrusion_width = 0
external_perimeter_speed = 50%
external_perimeters_first = 0
extra_perimeters = 0
extra_perimeters_on_overhangs = 0
extrusion_width = 0
fill_angle = 45
fill_density = 0%
fill_pattern = stars
first_layer_acceleration = 0
first_layer_acceleration_over_raft = 0
first_layer_extrusion_width = 0
first_layer_height = 0.1
first_layer_infill_speed = 0
first_layer_speed = 100%
first_layer_speed_over_raft = 30
fuzzy_skin = none
fuzzy_skin_point_dist = 0.8
fuzzy_skin_thickness = 0.3
gap_fill_enabled = 1
gap_fill_speed = 20
gcode_comments = 0
gcode_label_objects = disabled
gcode_resolution = 0.0125
gcode_substitutions = 
infill_acceleration = 0
infill_anchor = 600%
infill_anchor_max = 50
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0
infill_first = 0
infill_overlap = 10%
infill_speed = 80
inherits = 
interface_shells = 0
interlocking_beam = 0
interlocking_beam_layer_count = 2
interlocking_beam_width = 0.8
interlocking_boundary_avoidance = 2
interlocking_depth = 2
interlocking_orientation = 22.5
ironing = 0
ironing_flowrate = 15%
ironing_spacing = 0.1
ironing_speed = 15
ironing_type = top
layer_height = 0.1
max_print_speed = 80
max_volumetric_extrusion_rate_slope_negative = 0
max_volumetric_extrusion_rate_slope_positive = 0
max_volumetric_speed = 0
min_bead_width = 85%
min_feature_size = 25%
min_skirt_length = 0
mmu_segmented_region_interlocking_depth = 0
mmu_segmented_region_max_width = 0
notes = 
only_one_perimeter_first_layer = 0
only_retract_when_crossing_perimeters = 0
ooze_prevention = 0
output_filename_format = [input_filename_base].gcode
over_bridge_speed = 0
overhang_speed_0 = 15
overhang_speed_1 = 15
overhang_speed_2 = 20
overhang_speed_3 = 25
overhangs = 0
perimeter_acceleration = 0
perimeter_extruder = 1
perimeter_extrusion_width = 0
perimeter_generator = classic
perimeter_speed = 60
perimeters = 1
post_process = 
print_settings_id = Beeg
raft_contact_distance = 0.1
raft_expansion = 1.5
raft_first_layer_density = 90%
raft_first_layer_expansion = 3
raft_layers = 0
resolution = 0
scarf_seam_entire_loop = 0
scarf_seam_length = 20
scarf_seam_max_segment_length = 1
scarf_seam_on_inner_perimeters = 0
scarf_seam_only_on_smooth = 1
scarf_seam_placement = nowhere
scarf_seam_start_height = 0%
seam_gap_distance = 15%
seam_position = aligned
single_extruder_multi_material_priming = 1
skirt_distance = 6
skirt_height = 1
skirts = 0
slice_closing_radius = 0.049
slicing_mode = regular
small_perimeter_speed = 15
solid_infill_acceleration = 0
solid_infill_below_area = 70
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_width = 0
solid_infill_speed = 20
spiral_vase = 0
staggered_inner_seams = 0
standby_temperature_delta = -5
support_material = 0
support_material_angle = 0
support_material_auto = 0
support_material_bottom_contact_distance = 0
support_material_bottom_interface_layers = -1
support_material_buildplate_only = 0
support_material_closing_radius = 2
support_material_contact_distance = 0.2
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0.35
support_material_interface_contact_loops = 0
support_material_interface_extruder = 1
support_material_interface_layers = 3
support_material_interface_pattern = rectilinear
support_material_interface_spacing = 0
support_material_interface_speed = 100%
support_material_pattern = rectilinear
support_material_spacing = 2.5
support_material_speed = 60
support_material_style = grid
support_material_synchronize_layers = 0
support_material_threshold = 0
support_material_with_sheath = 1
support_material_xy_spacing = 50%
support_tree_angle = 40
support_tree_angle_slow = 25
support_tree_branch_diameter = 2
support_tree_branch_diameter_angle = 5
support_tree_branch_diameter_double_wall = 3
support_tree_branch_distance = 1
support_tree_tip_diameter = 0.8
support_tree_top_rate = 15%
thick_bridges = 0
thin_walls = 1
top_fill_pattern = rectilinear
top_infill_extrusion_width = 0.4
top_one_perimeter_type = none
top_solid_infill_acceleration = 0
top_solid_infill_speed = 15
top_solid_layers = 0
top_solid_min_thickness = 0
travel_acceleration = 0
travel_speed = 130
travel_speed_z = 0
wall_distribution_count = 1
wall_transition_angle = 10
wall_transition_filter_deviation = 25%
wall_transition_length = 100%
wipe_tower = 0
wipe_tower_acceleration = 0
wipe_tower_bridging = 10
wipe_tower_brim_width = 2
wipe_tower_cone_angle = 0
wipe_tower_extra_flow = 100%
wipe_tower_extra_spacing = 100%
wipe_tower_extruder = 0
wipe_tower_no_sparse_layers = 0
wipe_tower_width = 60
xy_size_compensation = 0

[filament:Black basic PLA]
bed_temperature = 0
bridge_fan_speed = 100
chamber_minimal_temperature = 0
chamber_temperature = 0
compatible_printers = 
compatible_printers_condition = printer_notes!~/.*NO_TEMPLATES.*/ and printer_notes!~/.*PRINTER_VENDOR_TRILAB.*/ and printer_notes!~/.*PRINTER_MODEL_MK4IS.*/ and ! (printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and num_extruders>1)
compatible_prints = 
compatible_prints_condition = 
cooling = 0
disable_fan_first_layers = 1
enable_dynamic_fan_speeds = 0
end_filament_gcode = ";END gcode for filament"
extrusion_multiplier = 1
fan_always_on = 0
fan_below_layer_time = 100
filament_abrasive = 0
filament_colour = #000000
filament_cooling_final_speed = 2
filament_cooling_initial_speed = 3
filament_cooling_moves = 1
filament_cost = 27.82
filament_density = 1.24
filament_deretract_speed = nil
filament_diameter = 1.75
filament_infill_max_crossing_speed = 0
filament_infill_max_speed = 0
filament_load_time = 0
filament_loading_speed = 14
filament_loading_speed_start = 19
filament_max_volumetric_speed = 0
filament_minimal_purge_on_wipe_tower = 0
filament_multitool_ramming = 0
filament_multitool_ramming_flow = 10
filament_multitool_ramming_volume = 10
filament_notes = ""
filament_purge_multiplier = 100%
filament_ramming_parameters = "130 120 2.70968 2.93548 3.32258 3.83871 4.58065 5.54839 6.51613 7.35484 7.93548 8.16129| 0.05 2.66451 0.45 3.05805 0.95 4.05807 1.45 5.97742 1.95 7.69999 2.45 8.1936 2.95 11.342 3.45 11.4065 3.95 7.6 4.45 7.6 4.95 7.6"
filament_retract_before_travel = nil
filament_retract_before_wipe = nil
filament_retract_layer_change = nil
filament_retract_length = nil
filament_retract_length_toolchange = nil
filament_retract_lift = 1
filament_retract_lift_above = nil
filament_retract_lift_below = nil
filament_retract_restart_extra = nil
filament_retract_restart_extra_toolchange = nil
filament_retract_speed = nil
filament_seam_gap_distance = nil
filament_settings_id = ""
filament_shrinkage_compensation_xy = 0%
filament_shrinkage_compensation_z = 0%
filament_soluble = 0
filament_spool_weight = 230
filament_stamping_distance = 0
filament_stamping_loading_speed = 20
filament_toolchange_delay = 0
filament_travel_lift_before_obstacle = nil
filament_travel_max_lift = nil
filament_travel_ramping_lift = nil
filament_travel_slope = nil
filament_type = PLA
filament_unload_time = 0
filament_unloading_speed = 20
filament_unloading_speed_start = 100
filament_vendor = Made for Prusa
filament_wipe = nil
first_layer_bed_temperature = 0
first_layer_temperature = 0
full_fan_speed_layer = 3
idle_temperature = nil
inherits = 
max_fan_speed = 100
min_fan_speed = 35
min_print_speed = 10
overhang_fan_speed_0 = 0
overhang_fan_speed_1 = 0
overhang_fan_speed_2 = 0
overhang_fan_speed_3 = 0
slowdown_below_layer_time = 10
start_filament_gcode = "; Filament gcode\n"
temperature = 0

[filament:CC3D Polycarbonate]
bed_temperature = 85
bridge_fan_speed = 100
chamber_minimal_temperature = 0
chamber_temperature = 0
compatible_printers = 
compatible_printers_condition = 
compatible_prints = 
compatible_prints_condition = 
cooling = 1
disable_fan_first_layers = 1
enable_dynamic_fan_speeds = 0
end_filament_gcode = "; Filament-specific end gcode"
extrusion_multiplier = 1
fan_always_on = 0
fan_below_layer_time = 30
filament_abrasive = 0
filament_colour = #2E3436
filament_cooling_final_speed = 3.4
filament_cooling_initial_speed = 2.2
filament_cooling_moves = 4
filament_cost = 24.99
filament_density = 1.22
filament_deretract_speed = nil
filament_diameter = 1.75
filament_infill_max_crossing_speed = 0
filament_infill_max_speed = 0
filament_load_time = 0
filament_loading_speed = 28
filament_loading_speed_start = 3
filament_max_volumetric_speed = 11
filament_minimal_purge_on_wipe_tower = 15
filament_multitool_ramming = 0
filament_multitool_ramming_flow = 10
filament_multitool_ramming_volume = 10
filament_notes = ""
filament_purge_multiplier = 100%
filament_ramming_parameters = "120 100 5.70968 6.03226 7 8.25806 9 9.19355 9.3871 9.77419 10.129 10.3226 10.4516 10.5161| 0.05 5.69677 0.45 6.15484 0.95 8.76774 1.45 9.20323 1.95 9.95806 2.45 10.3871 2.95 10.5677 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
filament_retract_before_travel = nil
filament_retract_before_wipe = nil
filament_retract_layer_change = nil
filament_retract_length = nil
filament_retract_length_toolchange = nil
filament_retract_lift = nil
filament_retract_lift_above = nil
filament_retract_lift_below = nil
filament_retract_restart_extra = nil
filament_retract_restart_extra_toolchange = nil
filament_retract_speed = nil
filament_seam_gap_distance = nil
filament_settings_id = ""
filament_shrinkage_compensation_xy = 0%
filament_shrinkage_compensation_z = 0%
filament_soluble = 0
filament_spool_weight = 172
filament_stamping_distance = 0
filament_stamping_loading_speed = 20
filament_toolchange_delay = 0
filament_travel_lift_before_obstacle = nil
filament_travel_max_lift = nil
filament_travel_ramping_lift = nil
filament_travel_slope = nil
filament_type = PC
filament_unload_time = 0
filament_unloading_speed = 90
filament_unloading_speed_start = 100
filament_vendor = Prusa Polymers
filament_wipe = nil
first_layer_bed_temperature = 90
first_layer_temperature = 260
full_fan_speed_layer = 0
idle_temperature = nil
inherits = 
max_fan_speed = 70
min_fan_speed = 20
min_print_speed = 8
overhang_fan_speed_0 = 0
overhang_fan_speed_1 = 0
overhang_fan_speed_2 = 0
overhang_fan_speed_3 = 0
slowdown_below_layer_time = 20
start_filament_gcode = "; Filament gcode\nM900 K{if printer_notes=~/.*PRINTER_MODEL_MINI.*/}{0.28/(nozzle_diameter[0]/0.4)}{else}{0.07/(nozzle_diameter[0]/0.4)}{endif} ; Linear Advance v1.5\n"
temperature = 255

[filament:CF-PLA]
bed_temperature = 60
bridge_fan_speed = 100
chamber_minimal_temperature = 0
chamber_temperature = 0
compatible_printers = 
compatible_printers_condition = printer_notes!~/.*NO_TEMPLATES.*/ and printer_notes!~/.*PRINTER_VENDOR_TRILAB.*/ and printer_notes!~/.*PRINTER_MODEL_MK4IS.*/ and ! (printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and num_extruders>1) and printer_model == "Snapmaker A250 Dual"
compatible_prints = 
compatible_prints_condition = 
cooling = 1
disable_fan_first_layers = 1
enable_dynamic_fan_speeds = 0
end_filament_gcode = ";END gcode for filament\nG0 X{wipe_tower_x} Y{wipe_tower_y}"
extrusion_multiplier = 1
fan_always_on = 1
fan_below_layer_time = 100
filament_abrasive = 0
filament_colour = #FF8000
filament_cooling_final_speed = 2
filament_cooling_initial_speed = 3
filament_cooling_moves = 1
filament_cost = 25.4
filament_density = 1.24
filament_deretract_speed = nil
filament_diameter = 1.75
filament_infill_max_crossing_speed = 0
filament_infill_max_speed = 0
filament_load_time = 0
filament_loading_speed = 14
filament_loading_speed_start = 19
filament_max_volumetric_speed = 0
filament_minimal_purge_on_wipe_tower = 0
filament_multitool_ramming = 0
filament_multitool_ramming_flow = 10
filament_multitool_ramming_volume = 10
filament_notes = ""
filament_purge_multiplier = 100%
filament_ramming_parameters = "130 120 2.70968 2.93548 3.32258 3.83871 4.58065 5.54839 6.51613 7.35484 7.93548 8.16129| 0.05 2.66451 0.45 3.05805 0.95 4.05807 1.45 5.97742 1.95 7.69999 2.45 8.1936 2.95 11.342 3.45 11.4065 3.95 7.6 4.45 7.6 4.95 7.6"
filament_retract_before_travel = nil
filament_retract_before_wipe = nil
filament_retract_layer_change = nil
filament_retract_length = nil
filament_retract_length_toolchange = nil
filament_retract_lift = nil
filament_retract_lift_above = nil
filament_retract_lift_below = nil
filament_retract_restart_extra = nil
filament_retract_restart_extra_toolchange = nil
filament_retract_speed = nil
filament_seam_gap_distance = nil
filament_settings_id = ""
filament_shrinkage_compensation_xy = 0%
filament_shrinkage_compensation_z = 0%
filament_soluble = 0
filament_spool_weight = 0
filament_stamping_distance = 0
filament_stamping_loading_speed = 20
filament_toolchange_delay = 0
filament_travel_lift_before_obstacle = nil
filament_travel_max_lift = nil
filament_travel_ramping_lift = nil
filament_travel_slope = nil
filament_type = PLA
filament_unload_time = 0
filament_unloading_speed = 20
filament_unloading_speed_start = 100
filament_vendor = Generic
filament_wipe = nil
first_layer_bed_temperature = 60
first_layer_temperature = 215
full_fan_speed_layer = 3
idle_temperature = nil
inherits = 
max_fan_speed = 100
min_fan_speed = 100
min_print_speed = 10
overhang_fan_speed_0 = 0
overhang_fan_speed_1 = 0
overhang_fan_speed_2 = 0
overhang_fan_speed_3 = 0
slowdown_below_layer_time = 5
start_filament_gcode = "; Filament gcode\n"
temperature = 210

[filament:Eolas Prints TPU 93A @CREALITY - Copy]
bed_temperature = 30
bridge_fan_speed = 100
chamber_minimal_temperature = 0
chamber_temperature = 0
compatible_printers = 
compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_CREALITY.*/
compatible_prints = 
compatible_prints_condition = 
cooling = 0
disable_fan_first_layers = 1
enable_dynamic_fan_speeds = 0
end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n"
extrusion_multiplier = 1.16
fan_always_on = 1
fan_below_layer_time = 20
filament_abrasive = 0
filament_colour = #4D9398
filament_cooling_final_speed = 3.4
filament_cooling_initial_speed = 2.2
filament_cooling_moves = 4
filament_cost = 34.99
filament_density = 1.21
filament_deretract_speed = nil
filament_diameter = 1.75
filament_infill_max_crossing_speed = 0
filament_infill_max_speed = 0
filament_load_time = 0
filament_loading_speed = 28
filament_loading_speed_start = 3
filament_max_volumetric_speed = 1.2
filament_minimal_purge_on_wipe_tower = 15
filament_multitool_ramming = 0
filament_multitool_ramming_flow = 10
filament_multitool_ramming_volume = 10
filament_notes = ""
filament_purge_multiplier = 100%
filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
filament_retract_before_travel = nil
filament_retract_before_wipe = nil
filament_retract_layer_change = nil
filament_retract_length = 0
filament_retract_length_toolchange = nil
filament_retract_lift = nil
filament_retract_lift_above = nil
filament_retract_lift_below = nil
filament_retract_restart_extra = nil
filament_retract_restart_extra_toolchange = nil
filament_retract_speed = nil
filament_seam_gap_distance = nil
filament_settings_id = ""
filament_shrinkage_compensation_xy = 0%
filament_shrinkage_compensation_z = 0%
filament_soluble = 0
filament_spool_weight = 0
filament_stamping_distance = 0
filament_stamping_loading_speed = 20
filament_toolchange_delay = 0
filament_travel_lift_before_obstacle = nil
filament_travel_max_lift = nil
filament_travel_ramping_lift = nil
filament_travel_slope = nil
filament_type = TPU
filament_unload_time = 0
filament_unloading_speed = 90
filament_unloading_speed_start = 100
filament_vendor = Eolas Prints
filament_wipe = nil
first_layer_bed_temperature = 30
first_layer_temperature = 235
full_fan_speed_layer = 2
idle_temperature = 130
inherits = 
max_fan_speed = 0
min_fan_speed = 100
min_print_speed = 15
overhang_fan_speed_0 = 0
overhang_fan_speed_1 = 0
overhang_fan_speed_2 = 0
overhang_fan_speed_3 = 0
slowdown_below_layer_time = 20
start_filament_gcode = "; Filament gcode\n"
temperature = 235

[filament:PETG]
bed_temperature = 80
bridge_fan_speed = 80
chamber_minimal_temperature = 0
chamber_temperature = 0
compatible_printers = 
compatible_printers_condition = printer_notes!~/.*NO_TEMPLATES.*/ and printer_notes!~/.*PRINTER_VENDOR_TRILAB.*/ and printer_notes!~/.*PRINTER_MODEL_MK4IS.*/ and ! (printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and num_extruders>1)
compatible_prints = 
compatible_prints_condition = 
cooling = 1
disable_fan_first_layers = 3
enable_dynamic_fan_speeds = 0
end_filament_gcode = "; Filament-specific end gcode\nM221 S100"
extrusion_multiplier = 0.75
fan_always_on = 0
fan_below_layer_time = 20
filament_abrasive = 0
filament_colour = #FF8000
filament_cooling_final_speed = 2
filament_cooling_initial_speed = 3
filament_cooling_moves = 1
filament_cost = 27.82
filament_density = 1.27
filament_deretract_speed = 25
filament_diameter = 1.75
filament_infill_max_crossing_speed = 0
filament_infill_max_speed = 0
filament_load_time = 0
filament_loading_speed = 14
filament_loading_speed_start = 19
filament_max_volumetric_speed = 0
filament_minimal_purge_on_wipe_tower = 0
filament_multitool_ramming = 0
filament_multitool_ramming_flow = 10
filament_multitool_ramming_volume = 10
filament_notes = ""
filament_purge_multiplier = 100%
filament_ramming_parameters = "130 120 2.70968 2.93548 3.32258 3.83871 4.58065 5.54839 6.51613 7.35484 7.93548 8.16129| 0.05 2.66451 0.45 3.05805 0.95 4.05807 1.45 5.97742 1.95 7.69999 2.45 8.1936 2.95 11.342 3.45 11.4065 3.95 7.6 4.45 7.6 4.95 7.6"
filament_retract_before_travel = nil
filament_retract_before_wipe = nil
filament_retract_layer_change = nil
filament_retract_length = 2
filament_retract_length_toolchange = nil
filament_retract_lift = nil
filament_retract_lift_above = nil
filament_retract_lift_below = 1
filament_retract_restart_extra = nil
filament_retract_restart_extra_toolchange = nil
filament_retract_speed = 25
filament_seam_gap_distance = nil
filament_settings_id = ""
filament_shrinkage_compensation_xy = 0%
filament_shrinkage_compensation_z = 0%
filament_soluble = 0
filament_spool_weight = 230
filament_stamping_distance = 0
filament_stamping_loading_speed = 20
filament_toolchange_delay = 0
filament_travel_lift_before_obstacle = nil
filament_travel_max_lift = nil
filament_travel_ramping_lift = nil
filament_travel_slope = nil
filament_type = PETG
filament_unload_time = 0
filament_unloading_speed = 20
filament_unloading_speed_start = 100
filament_vendor = Made for Prusa
filament_wipe = 1
first_layer_bed_temperature = 80
first_layer_temperature = 240
full_fan_speed_layer = 5
idle_temperature = nil
inherits = 
max_fan_speed = 40
min_fan_speed = 0
min_print_speed = 10
overhang_fan_speed_0 = 0
overhang_fan_speed_1 = 0
overhang_fan_speed_2 = 0
overhang_fan_speed_3 = 0
slowdown_below_layer_time = 15
start_filament_gcode = "; Filament gcode\nM221 S80"
temperature = 240

[filament:PLA]
bed_temperature = 60
bridge_fan_speed = 100
chamber_minimal_temperature = 0
chamber_temperature = 0
compatible_printers = 
compatible_printers_condition = printer_notes!~/.*NO_TEMPLATES.*/ and printer_notes!~/.*PRINTER_VENDOR_TRILAB.*/ and printer_notes!~/.*PRINTER_MODEL_MK4IS.*/ and ! (printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and num_extruders>1)
compatible_prints = 
compatible_prints_condition = 
cooling = 1
disable_fan_first_layers = 1
enable_dynamic_fan_speeds = 0
end_filament_gcode = ";END gcode for filament"
extrusion_multiplier = 1
fan_always_on = 1
fan_below_layer_time = 100
filament_abrasive = 0
filament_colour = #FF8000
filament_cooling_final_speed = 2
filament_cooling_initial_speed = 3
filament_cooling_moves = 1
filament_cost = 27.82
filament_density = 1.24
filament_deretract_speed = nil
filament_diameter = 1.75
filament_infill_max_crossing_speed = 0
filament_infill_max_speed = 0
filament_load_time = 0
filament_loading_speed = 14
filament_loading_speed_start = 19
filament_max_volumetric_speed = 0
filament_minimal_purge_on_wipe_tower = 0
filament_multitool_ramming = 0
filament_multitool_ramming_flow = 10
filament_multitool_ramming_volume = 10
filament_notes = ""
filament_purge_multiplier = 100%
filament_ramming_parameters = "130 120 2.70968 2.93548 3.32258 3.83871 4.58065 5.54839 6.51613 7.35484 7.93548 8.16129| 0.05 2.66451 0.45 3.05805 0.95 4.05807 1.45 5.97742 1.95 7.69999 2.45 8.1936 2.95 11.342 3.45 11.4065 3.95 7.6 4.45 7.6 4.95 7.6"
filament_retract_before_travel = nil
filament_retract_before_wipe = nil
filament_retract_layer_change = nil
filament_retract_length = nil
filament_retract_length_toolchange = nil
filament_retract_lift = 1
filament_retract_lift_above = nil
filament_retract_lift_below = 1.2
filament_retract_restart_extra = nil
filament_retract_restart_extra_toolchange = nil
filament_retract_speed = nil
filament_seam_gap_distance = nil
filament_settings_id = ""
filament_shrinkage_compensation_xy = 0%
filament_shrinkage_compensation_z = 0%
filament_soluble = 0
filament_spool_weight = 230
filament_stamping_distance = 0
filament_stamping_loading_speed = 20
filament_toolchange_delay = 0
filament_travel_lift_before_obstacle = nil
filament_travel_max_lift = nil
filament_travel_ramping_lift = nil
filament_travel_slope = nil
filament_type = PLA
filament_unload_time = 0
filament_unloading_speed = 20
filament_unloading_speed_start = 100
filament_vendor = Made for Prusa
filament_wipe = nil
first_layer_bed_temperature = 60
first_layer_temperature = 215
full_fan_speed_layer = 3
idle_temperature = nil
inherits = 
max_fan_speed = 100
min_fan_speed = 35
min_print_speed = 10
overhang_fan_speed_0 = 0
overhang_fan_speed_1 = 0
overhang_fan_speed_2 = 0
overhang_fan_speed_3 = 0
slowdown_below_layer_time = 10
start_filament_gcode = "; Filament gcode\n"
temperature = 215

[printer:Ender3v2 0.4mm]
autoemit_temperature_commands = 1
bed_custom_model = 
bed_custom_texture = 
bed_shape = 0x0,230x0,230x220,0x220
before_layer_gcode = ;BEFORE_LAYER_CHANGE\n;G92 E0\n;{layer_z}\n\n
between_objects_gcode = 
binary_gcode = 0
color_change_gcode = M600
cooling_tube_length = 5
cooling_tube_retraction = 91.5
default_filament_profile = "Generic PLA @CREALITY"
default_print_profile = "0.16 mm OPTIMAL (0.4 mm nozzle) @CREALITY"
deretract_speed = 40
end_gcode = {if max_layer_z < max_print_height}G1 Z{z_offset+min(max_layer_z+2, max_print_height)} F600 ; Move print head up{endif}\nG1 X5 Y{print_bed_max[1]*0.85} F{travel_speed*60} ; present print\n{if max_layer_z < max_print_height-10}G1 Z{z_offset+min(max_layer_z+70, max_print_height-10)} F600 ; Move print head further up{endif}\n{if max_layer_z < max_print_height*0.6}G1 Z{max_print_height*0.6} F600 ; Move print head further up{endif}\nM140 S0 ; turn off heatbed\nM104 S0 ; turn off temperature\nM107 ; turn off fan\nM84 X Y E ; disable motors
extra_loading_move = -2
extruder_clearance_height = 20
extruder_clearance_radius = 20
extruder_colour = #FCE94F
extruder_offset = 0x0
gcode_flavor = klipper
high_current_on_filament_swap = 0
host_type = prusalink
inherits = 
layer_gcode = ;AFTER_LAYER_CHANGE\n;{layer_z}
machine_limits_usage = time_estimate_only
machine_max_acceleration_e = 5000
machine_max_acceleration_extruding = 10000
machine_max_acceleration_retracting = 10000
machine_max_acceleration_travel = 500
machine_max_acceleration_x = 10000
machine_max_acceleration_y = 10000
machine_max_acceleration_z = 500
machine_max_feedrate_e = 60
machine_max_feedrate_x = 500
machine_max_feedrate_y = 500
machine_max_feedrate_z = 10
machine_max_jerk_e = 5
machine_max_jerk_x = 8
machine_max_jerk_y = 8
machine_max_jerk_z = 0.4
machine_min_extruding_rate = 0
machine_min_travel_rate = 0
max_layer_height = 0.32
max_print_height = 250
min_layer_height = 0.06
multimaterial_purging = 140
nozzle_diameter = 0.4
nozzle_high_flow = 1
parking_pos_retraction = 92
pause_print_gcode = PAUSE
prefer_clockwise_movements = 0
print_host = 
printer_model = ENDER3V2
printer_notes = Don't remove the following keywords! These keywords are used in the "compatible printer" condition of the print and filament profiles to link the particular print and filament profiles to this printer profile.\nPRINTER_VENDOR_CREALITY\nPRINTER_MODEL_ENDER3V2\nPRINTER_HAS_BOWDEN
printer_settings_id = 
printer_technology = FFF
printer_variant = 0.4
printer_vendor = 
printhost_apikey = 
printhost_cafile = 
remaining_times = 0
retract_before_travel = 2
retract_before_wipe = 70%
retract_layer_change = 1
retract_length = 1.25
retract_length_toolchange = 1
retract_lift = 1
retract_lift_above = 0
retract_lift_below = 1
retract_restart_extra = 0
retract_restart_extra_toolchange = 0
retract_speed = 40
silent_mode = 0
single_extruder_multi_material = 0
start_gcode = M109 S0\nM190 S0\nSTART_PRINT EXTRUDER_TEMP={first_layer_temperature[initial_extruder]} BED_TEMP={first_layer_bed_temperature[initial_extruder]}
template_custom_gcode = 
thumbnails = 32x32/PNG, 300x300/PNG
thumbnails_format = PNG
toolchange_gcode = 
travel_lift_before_obstacle = 0
travel_max_lift = 0
travel_ramping_lift = 0
travel_slope = 0
use_firmware_retraction = 0
use_relative_e_distances = 0
use_volumetric_e = 0
variable_layer_height = 1
wipe = 1
z_offset = 0

[printer:beeg plotter]
autoemit_temperature_commands = 1
bed_custom_model = 
bed_custom_texture = 
bed_shape = 0x0,1200x0,1200x1200,0x1200
before_layer_gcode = ;BEFORE_LAYER_CHANGE\n;G92 E0\n;{layer_z}\n\n
between_objects_gcode = 
binary_gcode = 0
color_change_gcode = M600
cooling_tube_length = 5
cooling_tube_retraction = 91.5
default_filament_profile = "Generic PLA @CREALITY"
default_print_profile = "0.16 mm OPTIMAL (0.4 mm nozzle) @CREALITY"
deretract_speed = 40
end_gcode = {if max_layer_z < max_print_height}G1 Z{z_offset+min(max_layer_z+2, max_print_height)} F600 ; Move print head up{endif}\nG1 X5 Y{print_bed_max[1]*0.85} F{travel_speed*60} ; present print\n{if max_layer_z < max_print_height-10}G1 Z{z_offset+min(max_layer_z+70, max_print_height-10)} F600 ; Move print head further up{endif}\n{if max_layer_z < max_print_height*0.6}G1 Z{max_print_height*0.6} F600 ; Move print head further up{endif}\nM140 S0 ; turn off heatbed\nM104 S0 ; turn off temperature\nM107 ; turn off fan\nM84 X Y E ; disable motors
extra_loading_move = -2
extruder_clearance_height = 20
extruder_clearance_radius = 20
extruder_colour = #FCE94F
extruder_offset = 0x0
gcode_flavor = klipper
high_current_on_filament_swap = 0
host_type = prusalink
inherits = 
layer_gcode = ;AFTER_LAYER_CHANGE\n;{layer_z}
machine_limits_usage = time_estimate_only
machine_max_acceleration_e = 5000
machine_max_acceleration_extruding = 10000
machine_max_acceleration_retracting = 10000
machine_max_acceleration_travel = 500
machine_max_acceleration_x = 10000
machine_max_acceleration_y = 10000
machine_max_acceleration_z = 500
machine_max_feedrate_e = 60
machine_max_feedrate_x = 500
machine_max_feedrate_y = 500
machine_max_feedrate_z = 10
machine_max_jerk_e = 5
machine_max_jerk_x = 8
machine_max_jerk_y = 8
machine_max_jerk_z = 0.4
machine_min_extruding_rate = 0
machine_min_travel_rate = 0
max_layer_height = 0.32
max_print_height = 250
min_layer_height = 0.06
multimaterial_purging = 140
nozzle_diameter = 0.4
nozzle_high_flow = 1
parking_pos_retraction = 92
pause_print_gcode = PAUSE
prefer_clockwise_movements = 0
print_host = 
printer_model = ENDER3V2
printer_notes = Don't remove the following keywords! These keywords are used in the "compatible printer" condition of the print and filament profiles to link the particular print and filament profiles to this printer profile.\nPRINTER_VENDOR_CREALITY\nPRINTER_MODEL_ENDER3V2\nPRINTER_HAS_BOWDEN
printer_settings_id = 
printer_technology = FFF
printer_variant = 0.4
printer_vendor = 
printhost_apikey = 
printhost_cafile = 
remaining_times = 0
retract_before_travel = 2
retract_before_wipe = 70%
retract_layer_change = 1
retract_length = 1.25
retract_length_toolchange = 1
retract_lift = 1
retract_lift_above = 0
retract_lift_below = 1
retract_restart_extra = 0
retract_restart_extra_toolchange = 0
retract_speed = 40
silent_mode = 0
single_extruder_multi_material = 0
start_gcode = M109 S0\nM190 S0\nSTART_PRINT EXTRUDER_TEMP={first_layer_temperature[initial_extruder]} BED_TEMP={first_layer_bed_temperature[initial_extruder]}
template_custom_gcode = 
thumbnails = 32x32/PNG, 300x300/PNG
thumbnails_format = PNG
toolchange_gcode = 
travel_lift_before_obstacle = 0
travel_max_lift = 0
travel_ramping_lift = 0
travel_slope = 0
use_firmware_retraction = 0
use_relative_e_distances = 0
use_volumetric_e = 0
variable_layer_height = 1
wipe = 1
z_offset = 0

[printer:beeg plotter (A1 Landscape)]
autoemit_temperature_commands = 1
bed_custom_model = 
bed_custom_texture = 
bed_shape = 0x0,841x0,841x574,0x574
before_layer_gcode = ;BEFORE_LAYER_CHANGE\n;G92 E0\n;{layer_z}\n\n
between_objects_gcode = 
binary_gcode = 0
color_change_gcode = M600
cooling_tube_length = 5
cooling_tube_retraction = 91.5
default_filament_profile = "Generic PLA @CREALITY"
default_print_profile = "0.16 mm OPTIMAL (0.4 mm nozzle) @CREALITY"
deretract_speed = 40
end_gcode = {if max_layer_z < max_print_height}G1 Z{z_offset+min(max_layer_z+2, max_print_height)} F600 ; Move print head up{endif}\nG1 X5 Y{print_bed_max[1]*0.85} F{travel_speed*60} ; present print\n{if max_layer_z < max_print_height-10}G1 Z{z_offset+min(max_layer_z+70, max_print_height-10)} F600 ; Move print head further up{endif}\n{if max_layer_z < max_print_height*0.6}G1 Z{max_print_height*0.6} F600 ; Move print head further up{endif}\nM140 S0 ; turn off heatbed\nM104 S0 ; turn off temperature\nM107 ; turn off fan\nM84 X Y E ; disable motors
extra_loading_move = -2
extruder_clearance_height = 20
extruder_clearance_radius = 20
extruder_colour = #FCE94F
extruder_offset = 0x0
gcode_flavor = klipper
high_current_on_filament_swap = 0
host_type = prusalink
inherits = 
layer_gcode = ;AFTER_LAYER_CHANGE\n;{layer_z}
machine_limits_usage = time_estimate_only
machine_max_acceleration_e = 5000
machine_max_acceleration_extruding = 10000
machine_max_acceleration_retracting = 10000
machine_max_acceleration_travel = 500
machine_max_acceleration_x = 10000
machine_max_acceleration_y = 10000
machine_max_acceleration_z = 500
machine_max_feedrate_e = 60
machine_max_feedrate_x = 500
machine_max_feedrate_y = 500
machine_max_feedrate_z = 10
machine_max_jerk_e = 5
machine_max_jerk_x = 8
machine_max_jerk_y = 8
machine_max_jerk_z = 0.4
machine_min_extruding_rate = 0
machine_min_travel_rate = 0
max_layer_height = 0.32
max_print_height = 250
min_layer_height = 0.06
multimaterial_purging = 140
nozzle_diameter = 0.35
nozzle_high_flow = 1
parking_pos_retraction = 92
pause_print_gcode = PAUSE
prefer_clockwise_movements = 0
print_host = 
printer_model = ENDER3V2
printer_notes = Don't remove the following keywords! These keywords are used in the "compatible printer" condition of the print and filament profiles to link the particular print and filament profiles to this printer profile.\nPRINTER_VENDOR_CREALITY\nPRINTER_MODEL_ENDER3V2\nPRINTER_HAS_BOWDEN
printer_settings_id = 
printer_technology = FFF
printer_variant = 0.4
printer_vendor = 
printhost_apikey = 
printhost_cafile = 
remaining_times = 0
retract_before_travel = 2
retract_before_wipe = 70%
retract_layer_change = 1
retract_length = 1.25
retract_length_toolchange = 1
retract_lift = 1
retract_lift_above = 0
retract_lift_below = 1
retract_restart_extra = 0
retract_restart_extra_toolchange = 0
retract_speed = 40
silent_mode = 0
single_extruder_multi_material = 0
start_gcode = M109 S0\nM190 S0\nSTART_PRINT EXTRUDER_TEMP={first_layer_temperature[initial_extruder]} BED_TEMP={first_layer_bed_temperature[initial_extruder]}
template_custom_gcode = 
thumbnails = 32x32/PNG, 300x300/PNG
thumbnails_format = PNG
toolchange_gcode = 
travel_lift_before_obstacle = 0
travel_max_lift = 0
travel_ramping_lift = 0
travel_slope = 0
use_firmware_retraction = 0
use_relative_e_distances = 0
use_volumetric_e = 0
variable_layer_height = 1
wipe = 1
z_offset = 0

[printer:beeg plotter (A1)]
autoemit_temperature_commands = 1
bed_custom_model = 
bed_custom_texture = 
bed_shape = 0x0,594x0,594x841,0x841
before_layer_gcode = ;BEFORE_LAYER_CHANGE\n;G92 E0\n;{layer_z}\n\n
between_objects_gcode = 
binary_gcode = 0
color_change_gcode = M600
cooling_tube_length = 5
cooling_tube_retraction = 91.5
default_filament_profile = "Generic PLA @CREALITY"
default_print_profile = "0.16 mm OPTIMAL (0.4 mm nozzle) @CREALITY"
deretract_speed = 40
end_gcode = {if max_layer_z < max_print_height}G1 Z{z_offset+min(max_layer_z+2, max_print_height)} F600 ; Move print head up{endif}\nG1 X5 Y{print_bed_max[1]*0.85} F{travel_speed*60} ; present print\n{if max_layer_z < max_print_height-10}G1 Z{z_offset+min(max_layer_z+70, max_print_height-10)} F600 ; Move print head further up{endif}\n{if max_layer_z < max_print_height*0.6}G1 Z{max_print_height*0.6} F600 ; Move print head further up{endif}\nM140 S0 ; turn off heatbed\nM104 S0 ; turn off temperature\nM107 ; turn off fan\nM84 X Y E ; disable motors
extra_loading_move = -2
extruder_clearance_height = 20
extruder_clearance_radius = 20
extruder_colour = #FCE94F
extruder_offset = 0x0
gcode_flavor = klipper
high_current_on_filament_swap = 0
host_type = prusalink
inherits = 
layer_gcode = ;AFTER_LAYER_CHANGE\n;{layer_z}
machine_limits_usage = time_estimate_only
machine_max_acceleration_e = 5000
machine_max_acceleration_extruding = 10000
machine_max_acceleration_retracting = 10000
machine_max_acceleration_travel = 500
machine_max_acceleration_x = 10000
machine_max_acceleration_y = 10000
machine_max_acceleration_z = 500
machine_max_feedrate_e = 60
machine_max_feedrate_x = 500
machine_max_feedrate_y = 500
machine_max_feedrate_z = 10
machine_max_jerk_e = 5
machine_max_jerk_x = 8
machine_max_jerk_y = 8
machine_max_jerk_z = 0.4
machine_min_extruding_rate = 0
machine_min_travel_rate = 0
max_layer_height = 0.32
max_print_height = 250
min_layer_height = 0.06
multimaterial_purging = 140
nozzle_diameter = 0.35
nozzle_high_flow = 1
parking_pos_retraction = 92
pause_print_gcode = PAUSE
prefer_clockwise_movements = 0
print_host = 
printer_model = ENDER3V2
printer_notes = Don't remove the following keywords! These keywords are used in the "compatible printer" condition of the print and filament profiles to link the particular print and filament profiles to this printer profile.\nPRINTER_VENDOR_CREALITY\nPRINTER_MODEL_ENDER3V2\nPRINTER_HAS_BOWDEN
printer_settings_id = 
printer_technology = FFF
printer_variant = 0.4
printer_vendor = 
printhost_apikey = 
printhost_cafile = 
remaining_times = 0
retract_before_travel = 2
retract_before_wipe = 70%
retract_layer_change = 1
retract_length = 1.25
retract_length_toolchange = 1
retract_lift = 1
retract_lift_above = 0
retract_lift_below = 1
retract_restart_extra = 0
retract_restart_extra_toolchange = 0
retract_speed = 40
silent_mode = 0
single_extruder_multi_material = 0
start_gcode = M109 S0\nM190 S0\nSTART_PRINT EXTRUDER_TEMP={first_layer_temperature[initial_extruder]} BED_TEMP={first_layer_bed_temperature[initial_extruder]}
template_custom_gcode = 
thumbnails = 32x32/PNG, 300x300/PNG
thumbnails_format = PNG
toolchange_gcode = 
travel_lift_before_obstacle = 0
travel_max_lift = 0
travel_ramping_lift = 0
travel_slope = 0
use_firmware_retraction = 0
use_relative_e_distances = 0
use_volumetric_e = 0
variable_layer_height = 1
wipe = 1
z_offset = 0

[printer:beeg plotter (A4)]
autoemit_temperature_commands = 1
bed_custom_model = 
bed_custom_texture = 
bed_shape = 0x0,210x0,210x297,0x297
before_layer_gcode = ;BEFORE_LAYER_CHANGE\n;G92 E0\n;{layer_z}\n\n
between_objects_gcode = 
binary_gcode = 0
color_change_gcode = M600
cooling_tube_length = 5
cooling_tube_retraction = 91.5
default_filament_profile = "Generic PLA @CREALITY"
default_print_profile = "0.16 mm OPTIMAL (0.4 mm nozzle) @CREALITY"
deretract_speed = 40
end_gcode = {if max_layer_z < max_print_height}G1 Z{z_offset+min(max_layer_z+2, max_print_height)} F600 ; Move print head up{endif}\nG1 X5 Y{print_bed_max[1]*0.85} F{travel_speed*60} ; present print\n{if max_layer_z < max_print_height-10}G1 Z{z_offset+min(max_layer_z+70, max_print_height-10)} F600 ; Move print head further up{endif}\n{if max_layer_z < max_print_height*0.6}G1 Z{max_print_height*0.6} F600 ; Move print head further up{endif}\nM140 S0 ; turn off heatbed\nM104 S0 ; turn off temperature\nM107 ; turn off fan\nM84 X Y E ; disable motors
extra_loading_move = -2
extruder_clearance_height = 20
extruder_clearance_radius = 20
extruder_colour = #FCE94F
extruder_offset = 0x0
gcode_flavor = klipper
high_current_on_filament_swap = 0
host_type = prusalink
inherits = 
layer_gcode = ;AFTER_LAYER_CHANGE\n;{layer_z}
machine_limits_usage = time_estimate_only
machine_max_acceleration_e = 5000
machine_max_acceleration_extruding = 10000
machine_max_acceleration_retracting = 10000
machine_max_acceleration_travel = 500
machine_max_acceleration_x = 10000
machine_max_acceleration_y = 10000
machine_max_acceleration_z = 500
machine_max_feedrate_e = 60
machine_max_feedrate_x = 500
machine_max_feedrate_y = 500
machine_max_feedrate_z = 10
machine_max_jerk_e = 5
machine_max_jerk_x = 8
machine_max_jerk_y = 8
machine_max_jerk_z = 0.4
machine_min_extruding_rate = 0
machine_min_travel_rate = 0
max_layer_height = 0.32
max_print_height = 250
min_layer_height = 0.06
multimaterial_purging = 140
nozzle_diameter = 0.15
nozzle_high_flow = 1
parking_pos_retraction = 92
pause_print_gcode = PAUSE
prefer_clockwise_movements = 0
print_host = 
printer_model = ENDER3V2
printer_notes = Don't remove the following keywords! These keywords are used in the "compatible printer" condition of the print and filament profiles to link the particular print and filament profiles to this printer profile.\nPRINTER_VENDOR_CREALITY\nPRINTER_MODEL_ENDER3V2\nPRINTER_HAS_BOWDEN
printer_settings_id = 
printer_technology = FFF
printer_variant = 0.4
printer_vendor = 
printhost_apikey = 
printhost_cafile = 
remaining_times = 0
retract_before_travel = 2
retract_before_wipe = 70%
retract_layer_change = 1
retract_length = 1.25
retract_length_toolchange = 1
retract_lift = 1
retract_lift_above = 0
retract_lift_below = 1
retract_restart_extra = 0
retract_restart_extra_toolchange = 0
retract_speed = 40
silent_mode = 0
single_extruder_multi_material = 0
start_gcode = M109 S0\nM190 S0\nSTART_PRINT EXTRUDER_TEMP={first_layer_temperature[initial_extruder]} BED_TEMP={first_layer_bed_temperature[initial_extruder]}
template_custom_gcode = 
thumbnails = 32x32/PNG, 300x300/PNG
thumbnails_format = PNG
toolchange_gcode = 
travel_lift_before_obstacle = 0
travel_max_lift = 0
travel_ramping_lift = 0
travel_slope = 0
use_firmware_retraction = 0
use_relative_e_distances = 0
use_volumetric_e = 0
variable_layer_height = 1
wipe = 1
z_offset = 0

[presets]
print = beeg2_ava.ini (Beeg)
sla_print = - default -
sla_material = - default -
printer = beeg plotter (A1)
filament = Black basic PLA
physical_printer =